This dimension is based on provisions in the 2004 ADA and ABA Accessibility Guidelines for maneuvering clearance where a clear floor or ground space is confined on all or part of three sides...
Search Results "Dimension"
Filters
Commonly Searched Documents
-
Wheelchair Spaces (M303.2)
-
Wheelbase Definition
The larger of the dimensions measured on the right and left side of the mobility device were considered for the analysis....
-
11B-604.9 Water closets and toilet compartments for children's use
TABLE 11B-604.9 SUGGESTED DIMENSIONS FOR CHILDREN’S USE SUGGESTED DIMENSIONS FOR WATER CLOSETS SERVING CHILDREN AGES 3 THROUGH 12 Ages...
-
Alterations [4.1.6(1)(f) & (k)]
Or, if an alteration involves replacing the cab but not the existing shaft, ADAAG recognizes that meeting the minimum car plan dimensions may not be technically feasible due to the existing...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches,...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
These dimensions and their resulting geometry are consistent with the ADA and ABA Accessibility Guidelines (36 CFR Part 1191, Appendix D, sections 306 and 308)....
-
4.10.3 Hall Call Buttons
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top. (See Fig. 20.) Buttons shall be raised or flush....
-
4.10.3 HALL CALL BUTTONS
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top (see Fig. 20). Buttons shall be raised or flush....
-
Size and Clearances [4.21.2]
The 36 by 36 inch dimension, measured to the interior finish, keeps front and side grab bars within reach from the seat....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Parallel Grab Bars
In finalizing this rule, the Board has sought to specify dimensions as a range instead of in absolute terms where possible to facilitate compliance without compromising accessibility....
-
Stacks [8.5]
Recommendation: Dimensions for turns around obstructions in 4.3.3 (ADAAG Figure 7) provide minimum space for maneuvering around stacks where a cross aisle at the end of stacks is not provided...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-405.7.2.1
Handrail extensions are not permitted to obstruct required clear landing dimensions except as allowed by the exception to Section 11B-307.2....
-
2. Question: What is the minimum width needed for a level boarding railroad passenger station platform to meet the accessibility requirements of the Americans with Disabilities Act (ADA)?
of 10 inches on tangent track and 13 inches on curves and a maximum vertical dimension of 5.5 inches. 49 CFR 37.42(f)....
-
11B-609.3 Spacing
The distance between the grab bar and wall is an exact dimension. Many disabled people rely heavily upon grab bars to maintain balance and prevent serious falls....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADA Standards] 405.7.5 Doorways....
-
Sampling Strategies
Age is a continuous variable, along which anthropometric dimensions change continuously....
-
304 Turning Space
The Department recognizes that the technical specifications for T-shaped and circular turning spaces in the 1991 and 2010 Standards, which are based on manual wheelchair dimensions, may...
-
Observations:
Observations: Wheelbase dimensions for manual wheelchairs and rear-wheel drive power chairs were similar to each other but slightly less than the wheelbase for front wheel drive...
-
Exterior Routes
Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...