Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Openings in floor or ground surfaces 1/2 inch maximum with long dimension...
Search Results "Dimension"
Filters
Commonly Searched Documents
-
Exterior Routes
-
2. REGULATORY BUILT-IN TOLERANCES
REGULATORY BUILT-IN TOLERANCES: California Building Code Section 1101B.5 indicates all dimensions are subject to conventional industry tolerances except where the requirement is stated as...
-
208.1.2
The facility may not reduce the required number or dimensions of those spaces, or unnecessarily increase the length of the accessible route from a parking space to the facility....
-
407.12.3.2.1 Height (Section-by-Section Analysis)
These dimensions and their resulting geometry are consistent with the ADA and ABA Accessibility Guidelines (36 CFR Part 1191, Appendix D, sections 306 and 308)....
-
4.35.4 Bench
Every accessible dressing room shall have a 24 in by 48 in (610 mm by 1220 mm) bench fixed to the wall along the longer dimension....
-
11B-812.6 Vehicle spaces
Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum. 2....
-
B. Restrooms
These specifications are derived from requirements for rail vehicles and represent compromises between space needed for use and constraints imposed by vehicle dimensions....
-
11B-812.6 Vehicle spaces
Exceptions: Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum...
-
Seating Locations
These dimensions allow people using mobility devices (e.g., wheelchairs, scooters, walkers, canes, and crutches) to independently enter and exit the room and move throughout the space, sit...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
The Committee proposes that this horizontal dimension be included for stretchers under the proposed rule....
-
A4.23.3 Clear Floor Space
The specific shower shown is designed to fit exactly within the dimensions of a standard bathtub....
-
A4.30.4 Raised and Brailled Characters and Pictorial Symbol Signs (Pictograms)
The standard dimensions for literary Braille are as follows: Dot diameter .059 in. Inter-dot spacing .090 in....
-
Clear Floor Space [4.20.2]
Clear Floor Space [4.20.2] Clear floor space at tubs, which is dimensioned according to the approach, may overlap required turning space within the room....
-
4.1.6(4)(a)
Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
-
Medical Device Manufacturers
supports; • Question 19 (c) on location and size of transfer supports; • Question 23 (a) on stirrups; • Question 24 (b) on positioning supports; • Question 29 (a) on alternative dimension...
-
Q5.) What dimensions and conditions can practitioners reasonably consider to be compliant when the conditions, as constructed, do not meet the technical requirements exactly and there are no official, published, industry-developed tolerances?
A5.) This is the most difficult question and the most subject to varying opinions. Sloped concrete and asphalt surfaces are an excellent example of this problem. To our...
-
8.5 Updating Standards in the Future
As noted above, the general population is increasingly overweight and obese; if population heights and weights change significantly, this might alter dimensions required for equipment accessibility...
-
4.1.2 Surface Design of Examination Tables and Chairs
., while patients’ weights are compressing the table’s or chair’s foam padding).Z This dimension is typically measured at the back of a patient’s knees and includes compression of the seat...
-
§382.67(a)
stowage of cargo in the cabin compartment) in the cabin of sufficient size to stow at least one typical adult-sized folding, collapsible, or break-down manual passenger wheelchair, the dimensions...
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
Because of these complex shapes, it is necessary to create a standard method by which to measure table seat dimensions....
-
References:
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
R402.3 Post-Mounted Objects
The base dimension shall be 64 mm (2.5 in) thick minimum....
-
Horizontal Alignment
The critical user for this dimension would be the inline skater....
-
Clear Floor or Ground Space: ADA Standard Section 1008.4.2
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....