Thigh breadth for this analysis was computed as the larger of two dimensions, the horizontal distance between the lateral (outer) aspect of the hips, and the horizontal distance between...
Search Results "Dimension"
Filters
Commonly Searched Documents
-
1. Thigh Breadth
-
M302.2.3 Size (Section-by-Section Analysis)
increased to 17 inches, a disability advocate recommended increasing the width to 23 inches, two of the commenters, accessibility consultant and disability advocate, stated that the proposed dimensions...
-
5.8.2.5 Toe Height Recommendation
A toe space dimension usually defines a static unobstructed space. However, in the case of mammography, as the breast platform moves up and down, the toe space changes....
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
Technical Requirements for Accessible Hiker/Pedestrian Trails
Wheelchair dimensions, clear space, maneuvering room, and reach ranges found in Architectural Barriers Act Accessibility Standards (ABAAS) are the basis for trail designs that maximize accessibility...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Bike Lane Width
The AASHTO Guide for the Development of Bicycle Facilities (p. 22) recommends a minimum width for bike lanes of 1.2 m (4 ft).(2) While this dimension appears to be adequate to accommodate...
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
The Committee easily supported this increase as existing equipment already meets or exceeds this dimension....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
Exceptions Considered for Wheelchair Spaces on Raised Platforms
Comments should include information on sources to support the dimensions, where possible....
-
Standing Supports (M304.3 and M305.3)
The 2004 ADA and ABA Accessibility Guidelines specify the following dimensions for grab bars to enable individuals with disabilities to firmly grasp the grab bars and support themselves...
-
M301.4 Lift Compatibility
The dimensions there are 150mm x 1000mm. Recommendation here is to shrink the 1120mm dimension to 1000mm (39”) dimension to harmonize with the international standard....
-
Transfer Surface Height (M301.2.1 and M302.2.1)
Patient support surfaces can be adjusted to heights outside the specified dimensions when not needed for patient transfer such as when performing diagnostic procedures....
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
This dimension allows a user to grab it from any point on the platform....
-
B. Slopes
.: in the direction of travel) not more than 1:20 (critical dimension of 1 1/4" or less)?...
-
What is an Accessible Seat and Who Can Use One?
Accessible seats are spaces specifically designed for wheelchairs and include features such as an accessible approach, location at grade, clear floor space, and larger dimensions....
-
The Purpose of FSORAG and FSTAG
The building blocks for accessible design are based mostly on wheelchair dimensions, clear space, maneuvering room, and reach ranges found in ABAAS because the dimensions, multiple moving...
-
C101.4 Units of Measurement (Section-by-Section Analysis)
This proposed section is new to the 255 Guidelines, and would clarify dimensions stated in the text of the guidelines or referenced standards....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
R304.2.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the ramp run....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Rationale for final recommendation The Committee considered the dimensions for rectangular seats in roll-in showers from the 2010 Standards; and the ideal chair width recommended in Architectural...
-
R304.3.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the pedestrian street crossing....