Authority: 42 U.S.C. 3535(d), 4153. Source: 36 FR 24437, Dec. 22, 1971, unless otherwise noted.
Search Results "ANSI/HFES: American National Standards Institute/ Human Factors and Ergonomics Society"
Commonly Searched Documents
-
24 CFR Part 40—Accessibility Standards for Design, Construction, and Alteration of Publicly Owned Residential Structures (with amendments issued through Feb. 1996)
-
Raised and Brailled Characters and Pictorial Symbol Signs [4.30.4]
0.245 in nominal line spacing of braille cells (center to center of nearest corresponding dots in adjacent lines) 0.400 in (Source: specification #800, National...
- Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
- Inpro Corporation IPC® 855 Handrail
- CRL Jackson 1200 Series Push Pad Door Exit Devices
- Gamco Surface Mounted Hand Dryer - DR-5128
-
11B-805 Medical care and long-term care facilities
ETA Editor's Note The numbering of subsections within Section 11B-805 is not aligned between CBC and 2010 ADA Standards....
-
GENERAL CONSIDERATIONS FOR TRAFFIC SIGNAL CONTROLLED ROUNDABOUT PEDESTRIAN CROSSINGS
The MUTCD standard calls for a minimum of two signal faces....
- NuStep T5 Recumbent Cross Trainer
-
List of Subjects in 36 CFR Part 1195
MEDICAL DIAGNOSTIC EQUIPMENT Sec. 1195.1 Standards....
-
Comparison of Single-User Toilet Room Layouts: Plan 3
Comparison of Single-User Toilet Room Layouts: Plan 3 1991 Standards and 2010 Standards Plan-3: Meets Both 1991 Standards and 2010 Standards 7’-0"...
-
Single Occupant Structures: ADA Standard Section 203.6
Section 203.6 covers scoping requirements of general exceptions for single occupant structures in the most current ADA Standards.
- citEcar Electric Vehicles - ADA Enclosed Passenger Shuttle Wheelchair Ramp
-
What Testing Accommodations Must Be Provided?
individual with a disability that impairs sensory, manual, or speaking skills, the examination results accurately reflect the individual´s aptitude or achievement level or whatever other factor...
-
"Direct Threat" to Self
However, as emphasized above, such determinations must be strictly based on valid medical analyses or other objective evidence related to this individual, using the factors set out above...
-
Introduction to Guidelines
In developing such a process, manufacturers should consider the following factors: Where market research is undertaken, including individuals with disabilities in target populations...
-
5.1.2 Transfer Surface High Height Recommendations for M301 and M302
Since one key factor in ease of transfer is locating the transfer surface near or at the same height as the seat of the wheeled mobility device, moving the minimum high point for adjustability...
-
Sight Lines
A variety of factors determine the quality of "vertical" sight lines, such as the distance from performance areas, row spacing, staggering of seats, and floor slope....
-
1.5 Accessible Route Requirements for Campus Settings
The following factors may apply to projects on existing campus facilities: • New construction on an existing site must be connected, as part of the basic project scope, with an accessible...
-
Issue 13: How can energy codes and LEED™ “Points” be made compatible with lighting design criteria that accommodate low vision persons?
Comment by Jim Woods: To a great extent, the Illuminating Engineering Society is silent about this issue. I’ve watched the evolution of ASHRAE Standard 90 since its inception in 1975....
-
11B-209.2 Type
[2010 ADA Standards] 209.2 Type. Where provided, passenger loading zones shall comply with 209.2....
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
-
REQUIREMENTS FOR ACCESSIBILITY
The updated Checklist includes provisions from the 2010 ADA Standards for Accessible Design (“2010 Standards”).3 Any alterations made to a polling place must comply with the 2010 Standards...
-
2. Referenced Documents
2.1 ASTM standards E867 Standard Terminology Relating to Vehicle-Pavement Systems E1364 Standard Test Method for Measuring Road Roughness by Static Level Method E1926 Standard...