Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
Search Results "9-1-1 Service"
-
11B-809.10.6.5 Thresholds
-
Organization of This Rule
ADA Chapter 1, ADA Chapter 2, and Chapters 3 through 10 of the 2004 ADA/ABA Guidelines, codified at 36 CFR part 1191, app. B and D (2009) will be referred to as the ‘‘2004 ADAAG.''...
-
Width and Length: ADA Standard Section 1002.4.4.1
Wheelchair spaces shall provide a clear width of 30 inches (760 mm) minimum and a clear length of 48 inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above the floor surface...
-
11B-1002.4.4.1 Width and length
Wheelchair spaces shall provide a clear width of 30 inches (762 mm) minimum and a clear length of 48 inches (1219 mm) minimum measured to 9 inches (229 mm) minimum above the floor surface...
-
11B-1002.4.4.1 Width and length
Wheelchair spaces shall provide a clear width of 30 inches (762 mm) minimum and a clear length of 48 inches (1219 mm) minimum measured to 9 inches (229 mm) minimum above the floor surface...
- AJW Architectural Products U852 Dual Stall Seat Cover Dispenser - Partition Mounted
- AJW Architectural Products U852H Dual Stall Seat Cover Dispenser w/ Flush Mounting - Partition Mounted
- Web Content Accessibility Guidelines (WCAG) 2.1 (June 2018)
- World Wide Web Consortium (W3C) Web Accessibility Initiative
-
219.3 Receivers
EXCEPTIONS: 1....
-
Changes in Level [§303]
Changes in Level [§303] Changes in level can be up to ¼” without treatment or ½” if beveled with a slope no steeper than 1:2....
-
1193.23(b)(3) (Advisory Guidance)
Paragraph (b)(3) Working Cooperatively with Appropriate Disability-Related Organizations 1....
-
Running Slope [1018.7.1]
The running slope of any segment of a beach access route must be no steeper than 1:10 (10 percent)....
-
505.6 Gripping Surface
Where provided, horizontal projections shall occur 1 1/2 inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1....
-
Department of Justice method
For a 1:50 slope this is 1/2 inch; for a 1:20 slope it is approximately 1 - 1/4 inch and for a 1:12 slope it is 2 inches."...
-
C102.6 International Standards Organization (ISO)
Copies of the referenced standards, may be obtained from International Organization for Standardization, ISO Central Secretariat, 1, ch. de la Voie-Creuse, CP 56 - CH-1211 Geneva 20, Switzerland...
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
A gripping surface with a diameter between 1¼ to 1½ inches is specified. Alternate shapes are permitted that allow a similar opposing grip....
-
E102.6 International Standards Organization (ISO)
Copies of the referenced standards may be obtained from International Organization for Standardization, ISO Central Secretariat, 1, ch. de la Voie-Creuse, CP 56 - CH-1211 Geneva 20, Switzerland...
-
Parking
., no greater than 1:50 or 2%)....
-
5. What factors are relevant in determining whether an individual does not oppose receiving services in an integrated employment setting?
workshops directly from secondary school settings, have been absent from the competitive labor market for long periods of time, or been given scant information about supported employment services...
-
B. Interior Ramps
Interior Ramps (1) Royal Street Entrance Interior Ramp - Defendants will rebuild this ramp so that it meets 2010 Standards §§ 206.2.4 and 405....
-
A. Access Board
The Access Board is an independent federal agency established by Section 502 of the Rehabilitation Act (29 U.S.C. 792).1 The Access Board is responsible for developing accessibility guidelines...
-
Escalators: ADA Standard Section 810.9
Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see “Referenced Standards” in Chapter 1) and shall have a clear...