Unit 12 1⁄2" (320mm) wide, proj. 4 7⁄8" (125mm) from wall. No controlled delivery....
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
Bobrick ClassicSeries Toilet Tissue Dispenser for Two Rolls B-2740
-
Applicability to Carrier Web Sites
the majority of commenters favored our proposal to apply the Web site accessibility requirements to primary carrier Web sites that market air transportation to the general public in the United...
-
Guardian Barrier-Free Safety Station with WideArea™ Eye/Face Wash GBF1909PCC
Profile of unit is “flattened” to comply with maximum height and knee clearance requirements....
-
General: ADA Standard Section 228.1
Section 228.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for depositories, vending machines, change machines, mail boxes, and fuel...
-
Bobrick ClassicSeries Toilet Tissue Dispenser for Single Roll B-2730
Unit 6 1/2" (165mm) wide, proj. 4 7⁄8" (125mm) from wall. No controlled delivery....
-
American Specialties Clothes/Towel Hook Strip 127
Unit has 6 mounting holes through back for front mounting....
-
Gamco Recessed Toilet Tissue Holder - 212
Unit 6 3/8" W, 6 3/8" H (162 x 162mm)....
-
ADA 25th Anniversary Information
This Tool Kit is a project of the ADA National Network and its ten regional ADA Centers across the United States that provide information, guidance and training on the Americans with Disabilities...
-
MAX-Ability, Inc.
We have served clients throughout the United States and Canada in fields as diverse as Assisted Living facilities, Adult Day Care programs, and individuals seeking to age in place....
-
Assisted Living Directory - Nebraska Assisted Living Facilities & Senior Care
The State Unit on Aging provides a helpful (.pdf) that outlines each of Nebraska’s Agencies on Aging , and the counties that they cover....
-
Toilet Paper Dispensers
provisions for toilet paper dispensers at section 604.7 of the 2010 Standards require the dispenser to be located seven inches minimum and nine inches maximum in front of the water closet measured...
-
Section 1630.2(j)(1)(i) Broad Construction; not a Demanding Standard
As Congress noted in the legislative history of the ADAAA, “[t]o be clear, the purposes section conveys our intent to clarify not only that ‘substantially limits’ should be measured by a...
-
Ramps
(See Part 2 of this document for tips on measuring running slopes and cross slopes.) If any part of the accessible route contains steps, it must be ramped....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Technical Memorandum TM 2013-14 Dining Surfaces
A measurement of 18” per person shall be used to calculate the number of seating and standing capacity of a dining surface....
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
-
Seat Width Evaluation
The additional platform width may also have been needed to accommodate larger individuals; however the size of the individual and seat width of the wheelchair were not measured and therefore...
-
1. Typical Issues
During an emergency, as a temporary measure, if additional accessible parking spaces are needed, a portable ramp can be provided in a parking space marked off by traffic cones to provide...
-
Clear Floor Space [4.16.2]
clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension is measured...
-
Signage [4.6.4]
A height of at least 60 inches (measured to the bottom edge) is generally advisable (taking care not to make the sign a protruding object), although a higher height is better for signs at...
-
Mounting Location and Height [4.30.6]
Recommendation: At signs containing pictograms or other non-tactile information, this should be measured to the centerline of the raised/ Braille portion so that it is not too low (or high...
-
Data acquisition
The ISO standard states to collect measurements in the direction with the highest vibrations....
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
