perceive the world, in part, through pressure and movement of materials and surfaces against our skin, and we sense the instantaneous positions of our limbs as we move through, and take the measure...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
Conclusion
-
Station 2-Three-Point Turn
At this station, active participants were asked to make a three-point turn and the width that they required was measured (figure 27)....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
RI Global
RI was a leader in the fight for the United Nations Convention on the Rights of Persons with Disabilities (CRPD) and since its adoption on December 13, 2006, RI has focused its advocacy...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
In determining these heights, project researchers measured the seat heights from underneath the buttocks at the center of the occupied seats, a spot likely to be lower than the front of...
-
Safe harbor for qualified small businesses regarding what is readily achievable. (Section-by-Section Analysis)
Advocacy groups both for individuals with disabilities and private businesses requested specific guidance on what measures were required for barrier removal. ...
-
2.1 Participant Recruitment and Sampling
Researchers at each of these sites were trained in the data collection methods and used the same measurement equipment to ensure consistency in measurement methods across sites....
-
4.3.5.3 180-degree turn around an obstacle
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
Section 36.301 Eligibility Criteria (Preamble, Section-by-Section Analysis)
§ 36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
2.4.2 Considerations of Manufacturers in Accessible MDE Design
MDE manufacturers believe that their usability requirements should include some measure of accessibility....
-
B. Survey, Compliance and Review of Polling Place Locations
Department concludes that the Board or the ThirdParty Expert has proposed a remedial provision that does not address the violation, then the Department will recommend a temporary remedial measure...
-
Section 36.301 Eligibility Criteria (Section-By-Section Analysis and Response to Comments)
Sec.36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-2620
Unit 10 3/4" W, 14" H, 4" D (275 x 355 x 100mm)....
-
Gamco Semi-Recessed Towel Dispenser - TD-4F
Description Unit fabricated of type 304 stainless steel with exposed surfaces having a #4 satin-finish....
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-2621
Unit 10 3/4" W, 7 1/8" H, 4" D (275 x 180 x 100mm)....
-
Bobrick Heavy Duty Recessed Soap Dish B-4380
Unit 7 3⁄16" W, 5" H (185 x 125mm). Rough Wall Opening: 6" W, 4" H, 4" min. depth (150 x 100 x 100mm)....
-
Bobrick Recessed Heavy-Duty Soap Dish and Bar B-4390
Unit 7 3⁄16" W, 5" H (185 x 125mm). Rough Wall Opening: 6" W, 4" H, 4" min. depth (150 x 100 x 100mm)....
-
American Specialties Automatic Roll Paper Towel Dispenser and Waste Receptacle 94696A
Proximity sensing no-touch unit dispenses a pre-set length per cycle from 8" or 9" (205 or 230 mm) wide, 800' (244 m) long rolls. 10 gal. (37.8 L) stainless steel waste receptacle....
-
Gamco Maximum Security Clothes Hook Front Mounted - MSA-18
Unit 1-1/2" W x 3-3/8" H (38 x 86mm)....
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-26212
Unit 10 3/4" W, 7 1/8" H, 4" D (275 x 180 x 100mm)....
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-262
Unit 10 3/4" W, 14" H, 4" D (275 x 355 x 100mm)....
