(3) At least one accessible route shall connect accessible building or facility entrances with all accessible spaces and elements and with all accessible dwelling units within the building...
Search Results "Unit of Measurement"
-
1127B.1
-
224.5 Dispersion
(3) Facilities with residential units and transient lodging units....
-
A. Background
The parties to this Settlement Agreement (“Agreement”) are the United States of America, Thomas Jefferson University Hospitals, Inc., and Outpatient Imaging Affiliates, LLC., collectively...
-
Haws Fountain Skirt SK3
Model SK3 is a wrap around satin finish stainless steel cane touch skirt for installation on the high unit to comply with ADA protruding objects guidelines....
-
Design of Shared Use Paths, Street Intersections, and Midblock Crossings
nor the pedestrian is the design "vehicle" or user for shared use paths, their intersections with roadways, or for a host of other features throughout the transportation system of the United...
-
Bradley Terreon Classroom Sink TCS Series
Terreon solid surface and TerreonRE recycled solid surface are now GREENGUARD Certified as low-emitting materials TAS compliant units available Coved backsplash Drilled or equipped...
-
Accessible Routes (Exterior and Interior)
(See Part 2 of this document for tips on taking measurements.)...
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
Curb Ramps at Marked Crossings and Vehicular Lanes
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured...
-
3. Modified Theaters
Therefore, when wheelchair spaces are relocated one or more row[s] farther back from the screen, that movement is measured from the existing seating plan....
-
Contrast
Commenters considered this provision to be of questionable usefulness and difficult to meet absent a recognized method of measuring resiliency or sound-on-cane contact. Response....
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
j) Safety Hazards Policy
Though Kirola complained of steep paths at Alamo Square Park, the probative value of such testimony is undermined by the lack of any objective data (such as actual measurements of those...
-
Transfer Access [1014.2.1]
The camp shelter floor at the entrance or opening must be no higher than 19 inches when measured from the clear ground space....
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
This depth measurement is from the center-point of the front and back of the transfer surface as shown in Figure 5.2.1.1....
-
Front grab bar protocol
The preferred grab bar height was measured between the floor and the top of the grab bar surface. ...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
The cross slope is measured perpendicular to the direction of pedestrian travel....
-
Carpet [4.5.3]
A pile thickness up to ½ inch (measured to the backing, cushion, or pad) is allowed, although a lower pile provides easier wheelchair maneuvering....
-
Bails et al.
Research findings from many of the field tests used pre-established sizes and features to measure barriers and problems....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
§ 38.175(a)
All doorways shall have, when the door is open, at least 2 footcandles of illumination measured on the door threshold....
-
11B-707.4 Privacy
., a covered entity does not have to take measures that would result in a fundamental alteration of its program or would cause undue burdens, provide adequate protection to operators of...
-
F105.2.3 ASTM
ASTM F 1292-99 and ASTM F 1292-04 establish a uniform means to measure and compare characteristics of surfacing materials to determine whether materials provide a safe surface under and...
