As Congress noted in the legislative history of the ADAAA, “[t]o be clear, the purposes section conveys our intent to clarify not only that ‘substantially limits’ should be measured by a...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
Section 1630.2(j)(1)(i) Broad Construction; not a Demanding Standard
-
Ramps
(See Part 2 of this document for tips on measuring running slopes and cross slopes.) If any part of the accessible route contains steps, it must be ramped....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Technical Memorandum TM 2013-14 Dining Surfaces
A measurement of 18” per person shall be used to calculate the number of seating and standing capacity of a dining surface....
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
-
Seat Width Evaluation
The additional platform width may also have been needed to accommodate larger individuals; however the size of the individual and seat width of the wheelchair were not measured and therefore...
-
1. Typical Issues
During an emergency, as a temporary measure, if additional accessible parking spaces are needed, a portable ramp can be provided in a parking space marked off by traffic cones to provide...
-
Clear Floor Space [4.16.2]
clear floor space doors cannot swing into the clear floor space required at any fixture the 18 inch water closet centerline is absolute The 18 inch dimension is measured...
-
Signage [4.6.4]
A height of at least 60 inches (measured to the bottom edge) is generally advisable (taking care not to make the sign a protruding object), although a higher height is better for signs at...
-
Mounting Location and Height [4.30.6]
Recommendation: At signs containing pictograms or other non-tactile information, this should be measured to the centerline of the raised/ Braille portion so that it is not too low (or high...
-
Data acquisition
The ISO standard states to collect measurements in the direction with the highest vibrations....
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
Conclusion
perceive the world, in part, through pressure and movement of materials and surfaces against our skin, and we sense the instantaneous positions of our limbs as we move through, and take the measure...
-
Station 2-Three-Point Turn
At this station, active participants were asked to make a three-point turn and the width that they required was measured (figure 27)....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
In determining these heights, project researchers measured the seat heights from underneath the buttocks at the center of the occupied seats, a spot likely to be lower than the front of...
-
Safe harbor for qualified small businesses regarding what is readily achievable. (Section-by-Section Analysis)
Advocacy groups both for individuals with disabilities and private businesses requested specific guidance on what measures were required for barrier removal. ...
-
2.1 Participant Recruitment and Sampling
Researchers at each of these sites were trained in the data collection methods and used the same measurement equipment to ensure consistency in measurement methods across sites....
-
4.3.5.3 180-degree turn around an obstacle
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
RI Global
RI was a leader in the fight for the United Nations Convention on the Rights of Persons with Disabilities (CRPD) and since its adoption on December 13, 2006, RI has focused its advocacy...
