In United States v....
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
II. ENFORCING THE ADA PART 2
-
American Specialties Automatic Roll Paper Towel Dispenser and Waste Receptacle 04692A
Proximity sensing no-touch unit dispenses a pre-set length per cycle from 8" or 9" (205 or 230 mm) wide, 800' (244 m) long rolls. Battery operated (4) D-size....
-
NFPA
Revise Section 10.3.3 as follows: 10.3.3 All devices and appliances that receive their power from the initiating device circuit or signaling line circuit of a control unit shall be California...
-
Spacing: ADA Standard Section 609.3
Section 609.3 covers the current ADA Standards for the grab bar spacing between the wall, objects above, below and at the ends of the grab bar.
-
Bobrick Clothes Hook B-233
Unit is 2 1⁄4" (55mm) high....
-
Section 36.301 Eligibility Criteria (Preamble, Section-by-Section Analysis)
§ 36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
2.4.2 Considerations of Manufacturers in Accessible MDE Design
MDE manufacturers believe that their usability requirements should include some measure of accessibility....
-
B. Survey, Compliance and Review of Polling Place Locations
Department concludes that the Board or the ThirdParty Expert has proposed a remedial provision that does not address the violation, then the Department will recommend a temporary remedial measure...
-
Section 36.301 Eligibility Criteria (Section-By-Section Analysis and Response to Comments)
Sec.36.301 provides that public accommodations may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures...
-
Bobrick Koala Kare Oval, Wall Mounted Baby Changing Station KB208
Thesteel pivot rod secured in a metal tube offers sustained resistance to wear and improved durability and the gas spring mechanism ensures smooth open and close of the unit....
-
AJW Architectural Products US39 Collapsable Security Hook Strip 18"L, 4 Hooks, Exposed Mounting - Surface Mounted
Product Features Fabricated of #14 gauge stainless steel with a #4 satin finish Hooks collapse to prevent injury Exposed mounting Unit is designed for security applications...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
5.1.1 Transfer Surface Height Adjustability Recommendation for M301 and M302
In determining these heights, project researchers measured the seat heights from underneath the buttocks at the center of the occupied seats, a spot likely to be lower than the front of...
-
Safe harbor for qualified small businesses regarding what is readily achievable. (Section-by-Section Analysis)
Advocacy groups both for individuals with disabilities and private businesses requested specific guidance on what measures were required for barrier removal. ...
-
2.1 Participant Recruitment and Sampling
Researchers at each of these sites were trained in the data collection methods and used the same measurement equipment to ensure consistency in measurement methods across sites....
-
4.3.5.3 180-degree turn around an obstacle
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
Toilet Paper Dispensers
provisions for toilet paper dispensers at section 604.7 of the 2010 Standards require the dispenser to be located seven inches minimum and nine inches maximum in front of the water closet measured...
-
Section 1630.2(j)(1)(i) Broad Construction; not a Demanding Standard
As Congress noted in the legislative history of the ADAAA, “[t]o be clear, the purposes section conveys our intent to clarify not only that ‘substantially limits’ should be measured by a...
-
Ramps
(See Part 2 of this document for tips on measuring running slopes and cross slopes.) If any part of the accessible route contains steps, it must be ramped....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Technical Memorandum TM 2013-14 Dining Surfaces
A measurement of 18” per person shall be used to calculate the number of seating and standing capacity of a dining surface....
-
5.1 Transfer Surface Height Recommendations
The height of the transfer surface during patient transfer shall be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer surface....
