Application and Scoping Requirements), C203.1, C203.1 Exception, C203.1.1, C205.2, C205.2 Exception 2, C205.2 Exception 3, C205.2.1, C205.3; and Appendix C (Functional Performance Criteria and Technical...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
702.10.1 WCAG 2.0, Web Content Accessibility Guidelines
-
Chapter 3: Functional Performance Criteria (Section-by-Section Analysis)
Chapter 3 contains proposed functional performance criteria, which are outcome-based provisions that apply when applicable technical requirements (i.e., Chapters 4 and 5) do not address...
-
Research Projects
The Board sponsors and coordinates research for use in developing accessibility guidelines and providing technical assistance to the public....
-
11B-812 Electric vehicle charging stations
However, the absence of scoping or technical requirements in the Standards would make it difficult to conclude what that means....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
Specifically, the Access Board indicated it was considering requiring circular cross sections to have an outside diameter of 1¼ inches minimum and 2 inches maximum, and transfer supports...
-
§382.29(b)(4)
If the passenger fails to meet this notice requirement, however, you must still accommodate him or her to the extent practicable....
-
Withdrawal of Outstanding NPRMs
To the extent that those proposals were incorporated in the 2004 ADAAG, they will all be included in the Department's proposed standards....
-
Withdrawal of Outstanding NPRMs
To the extent that those proposals were incorporated in the 2004 ADAAG, they will all be included in the Department's proposed standards....
-
Wheelchair Transfer
The type and extent of disability, the configuration of fixtures, and the availability of space alongside water closets often determine the technique used....
-
1.4.4. Operational Requirements
This requirement applies to the extent that a movie theater intends to comply with this rulemaking by providing open movie captioning at all showings or on-demand whenever requested by or...
-
25. Need for Return Trip Assistance
To the extent that this need is predictable, it should be handled in advance, either as part of the eligibility process or the provider's reservations process....
-
25. Need for Return Trip Assistance
To the extent that this need is predictable, it should be handled in advance, either as part of the eligibility process or the provider's reservations process....
-
11B-246.1 General
agency finds that, in specific areas, the natural environment would be materially damaged by compliance with these regulations, such areas shall be subject to these regulations only to the extent...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
703.2.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
R410.10 Line Spacing
Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
T303.3.1 Seat-Back Handhold Cross Section
The cross section of seat-back handholds shall have an outside diameter of 7/8 inches (22 mm) minimum and 2 inches (50 mm) maximum....
-
T402.8.2 Deployment to Boarding Platforms
The running slope of ramps and bridgeplates used for deployment to platforms shall be 1:8 maximum, as measured to the boarding platform with the non-rail vehicle resting on a flat surface...