Terms not listed in Section 11B-106.5 and not defined in Chapter 2, Section 202, but specifically defined in a referenced standard, shall have the specified meaning from the referenced standard...
Search Results "Grade 2 Braille"
-
11B-106.2 Terms defined in referenced standards
-
§ 36.601 Submitting official
official means the State or local official who – (1) Has principal responsibility for administration of a code, or is authorized to submit a code on behalf of a jurisdiction; and (2)...
-
Recreation Site
An area that is improved, developed, or otherwise identified for recreation and that has a development scale of 0, 1, 2, 3, 4, or 5 (See Forest Service Handbook 2309.13, Chapter 10 – Exhibit...
-
7.4.3.2 Cross Slope
Where the surface is paved or is elevated above the natural ground, the cross slope shall not be steeper than 1:48 (2 percent). ...
-
E102.7.2 ITU-T Recommendation E.161
Arrangement of digits, letters and symbols on telephones and other devices that can be used for gaining access to a telephone network, ITU – T Study Group 2, (February 2001), IBR proposed...
-
FAQ: How do I submit a job for the Job Board?
Click on the "FEEDBACK OR HELP" button that appears on every page of Corada. 2. Contact us via email....
-
§1630.2(p)(1) In general
means, with respect to the provision of an accommodation, significant difficulty or expense incurred by a covered entity, when considered in light of the factors set forth in paragraph (p)(2)...
-
33.
. § 12188(b)(2)(c), to vindicate the public interest....
-
§ 38.101(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate shall have, when the door is open, at least 2 footcandles of illumination measured on the step tread, ramp, bridge plate, or...
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-106.2 Terms defined in referenced standards
Terms not listed in Section 11B-106.5 and not defined in Chapter 2, Section 202, but specifically defined in a referenced standard, shall have the specified meaning from the referenced standard...
-
11B-810.10 Track crossings
Exception: Openings for wheel flanges shall be permitted to be 2½ inches (64 mm) maximum....
-
11B-810.10 Track crossings
Exception: Openings for wheel flanges shall be permitted to be 2½ inches (64 mm) maximum....
-
11B-106.2 Terms defined in referenced standards
Terms not listed in Section 11B-106.5 and not defined in Chapter 2, Section 202, but specifically defined in a referenced standard, shall have the specified meaning from the referenced standard...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Allegion Falcon RU/RW Series Mechanical Locks
It exceeds ANSI Grade 1 specifications and is UL/ULC listed. Incorporates Falcon’s vandal resistant Pressure Release™ trim to prevent damage to internal mechanism....
-
Panda TS.19 Thermally Broken Lift & Slide System
Trench Depth: Min. 2 1/2″ ADA Compliant Standard Track. Recessed into sub-floor to ensure the smoothest possible operation....
-
11B-1003.2.2 Boarding piers at boat launch ramps
Accessible routes serving floating boarding piers shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in Section 11B-1003.2.1. 2. ...
-
11B-246.1 General
environment would be materially damaged by compliance with these regulations, such areas shall be subject to these regulations only to the extent that such material damage would not occur. 2....
-
Handrails
Handrails must comply with the following: Clearance between handrail gripping surfaces and adjacent surfaces shall be 1 1/2 inches (38 mm) minimum. ...
-
Implication for Standards and Design
Close to 200 community dwelling adults who independently transfer have been evaluated during phases 1 and 2 combined of this multi-year study. ...
-
§35.130(b)(1)(iv) (Section-by-Section Analysis)
Paragraph (b)(1)(iv) must be read in conjunction with paragraphs (b)(2), (d), and (e)....
