(2) Aircraft with 100 or more passenger seats shall have a priority space in the cabin designated for stowage of at least one folding wheelchair; (3) Aircraft with more than one aisle...
Search Results "Parking Space Length"
-
§ 382.21 Aircraft accessibility
-
A. ACCESSIBLE SEATING
space requirements set forth in table 221.2.1.1 of the Standards....
-
232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with 807.2.3....
-
11B-232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
-
11B-232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
-
11B-232.2.1.1 Beds
In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with Section 11B-807.2.3....
-
Reach Ranges and Operable Parts
OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2 Clear floor space...
-
Reach Ranges and Operable Parts
OPERABLE PARTS Forward and side reach 11B-308.2/3 Over projections 11B-308.2.2/3.2 Clear floor space...
-
Guidelines for Requirement 2
The Department has retained the applicable provisions of the ANSI Standard for parking space....
-
1011.2.1 Size and Location
The size and location of the clear ground space shall be in accordance with Table 1011.2.1. ...
-
M102.1 Defined Terms (Section-by-Section Analysis)
decided to add six additional terms to this section; end transfer surface, examination chair, imagining [sic] equipment with bores, imagining [sic] bed, side transfer surface, and wheelchair space...
- Bosch Power Tools - GPL-3 3 Point Laser
-
28.1 Q. If an architect or builder chooses to follow the bathroom specifications in Requirement 7...are the other bathrooms in the dwelling unit required to have reinforced walls for grab bars?
A. Yes. Requirement 6 of the Guidelines requires reinforced walls in bathrooms for later installation of grab bars. Even though Requirement 6 was not repeated under Requirement...
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5....
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5....
-
Fishing Facilities
Word Fillable Form (0.8MB) Word Non-Fillable Form (0.8MB) PDF Non-Fillable Form (0.7MB)
-
1011.2.1 Size and Location
The size and location of the clear ground space shall be in accordance with Table 1011.2.1....
- EVSE Garage Overhead EV (Electric Vehicle) Charger for Parking Garages & Multi-Dwelling Units
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
M303.3.3 Ramped
Changes in level greater than ½ inch (13 mm) high shall be ramped and shall comply with M303.3.3.
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height. Edge protection is not required on platforms 1 ½ inches or less in height.
-
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations
5.8.1.2.2 Single Ramped Entry - Edge Protection on the Platform and Platform Sides Recommendations The Committee recommends a two-inch high edge protection on the back of the...
-
5.8.1.2.1 Ramped Entry Slope
5.8.1.2.1 Ramped Entry Slope. Raised platforms should have a ramp with slopes that do not exceed the following: Rise 0 to 1 ½ inches – 1:2 Slope Rise >1 ½ to 2 ½ inches – 1:8...