Where the diagnostic equipment is used in a reclined position, head and back support shall be provided....
Search Results "Patient in Side-Lying Position"
-
M302.3.3 Head and Back Support
-
5.2.3 Transfer Surface Measurement
The transfer surface should be measured from the center-point of each side of the transfer surface....
-
Guldmann Sling Instruction: How to put on the Basic High Comfort Sling on in Bed
Instruction in how to put on the Basic High Comfort sling when the patient is lying in bed....
-
Facilities Specializing in Treating Conditions That Affect Mobility: ADA Standard Section 223.2.2
Section 223.2.2 covers scoping requirements in the current ADA Standards for facilities specializing in treating conditions that affect mobility.
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum.
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface.
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high...
-
11B-407.4.8 Car position indicators
Audible and visible car position indicators shall be provided in elevator cars....
-
11B-407.4.8 Car position indicators
Audible and visible car position indicators shall be provided in elevator cars....
-
M304.2.1 Slip Resistant
The surface on which the patient stands shall be slip resistant....
-
M304.2 Standing Surface
The surface on which the patient stands shall be slip resistant....
-
M304.2 Standing Surface
Equipment surfaces on which patients stand must comply with M304.2...
-
Is additional latch side clearance required on the push side of doors with a forward approach when either a latch or closer (but not both) is provided?
No, latch clearance 12” minimum is required for forward approaches on the push-side of doors equipped with both a closer and a latch....
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10.
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
Patient Toilet Rooms [6.4]
Patient Toilet Rooms [6.4] ADAAG specifications are based on the independent use of toilet and bathing facilities and do not address alternate designs for assisted use....
-
Patient Bedrooms [6.3]
[See subsections ...]
-
Hill-Rom Sabina® II Mobile Lift
Sabina II lift meets the needs of a wide range of patients by offering the ability to adapt each raising or lifting operation to the capabilities of the individual patient....
-
vii. Ancillary equipment
Ancillary equipment includes items such as positioning straps or cushions; protective padding; adjustable, padded leg supports for gynecological examinations; and additional supports, rails...
-
M302.2.1 Adjustability
A low transfer position at a height of 17 inches (430 mm) minimum and 19 inches (485 mm) maximum; B. A high transfer position at 25 inches (635 mm); and C....
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3.
-
M305.3 Standing Supports (Section-by-Section Analysis)
M305.3 provides the technical requirements for standing supports which are required on diagnostic equipment covered by M304. This provision has been reorganized in the final rule...
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3.
-
R406.3 Unobstructed Side Reach
R406.3 Unobstructed Side Reach....
