Section 407.4.8.1.2 covers the current ADA Standards for the location of visible elevator car position indicators.
Search Results "Patient in Side-Lying Position"
Filters
Commonly Searched Documents
-
Location: ADA Standard Section 407.4.8.1.2
-
1. Standing Supports
It is important that the patients’ hands do not accidentally hit these controls when they are holding the positioning supports....
-
M302.2.1 Adjustability (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface height range for diagnostic equipment used by patients in a seated position of 17 inches minimum and 19 inches maximum....
-
M304.3 Standing Supports
Standing supports shall be provided on each side of the standing surface and shall comply with M305.3....
-
M303.1 General (Section-by-Section Analysis)
This is an introductory section.
-
11B-406.2.2 Sides of curb ramps
FIGURE 11B-406.2.2 ‡‡ SIDES OF CURB RAMPS...
-
Clearances for Side Approaches
Clearances for Side Approaches Clearance for side approaches are based on the swing of doors, direction of approach (hinge or latch), and the provision of closers (in some cases latches...
-
703.3.2 Position
Braille shall be positioned below the corresponding text. If text is multi-lined, braille shall be placed below the entire text....
-
11B-243.1 General
Where shooting facilities with firing positions are designed and constructed at a site, at least 5 percent, but no fewer than one, of each type of firing position shall comply with Section...
-
Hospital Patient Toilet Rooms
Hospital Patient Toilet Rooms....
-
Visible Indicators: ADA Standard Section 407.4.8.1
Section 407.4.8.1 covers the current ADA Standards for visible elevator car position indicators.
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply...
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface.
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of...
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the...
-
6.4 Patient Toilet Rooms
Where toilet/bath rooms are provided as a part of a patient bedroom, each patient bedroom that is required to be accessible shall have an accessible toilet/bath room that complies with 4.22...
-
11B-604.5.1 Side wall
The side wall grab bar shall be 42 inches (1067 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1372 mm) minimum from the rear wall with...
-
M302.1 General (Section-by-Section Analysis)
The MDE NPRM proposed that all diagnostic equipment used by patients in a seated position must comply with the technical requirements of proposed section M302....
-
The Association of Safe Patient Handling Professionals
The Association of Safe Patient Handling Professionals is a 501(c)(3) non-profit organization that brings together like-minded individuals that want to share ideas, support research, and...
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
In a wheelchair accessible compartment with a door located in the side wall or partition, either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide and 60 inches (1524 mm) deep...
-
6.3(5)
(5) Each bedroom shall have a door that complies with 4.13.
-
6.4 PATIENT TOILET ROOMS
Provide each patient bedroom that is required to be accessible with an accessible toilet room that complies with 4.22 or 4.23....
-
M302.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and comply with M305.4.
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
