If any provision of this Agreement is determined to be invalid, unenforceable, or otherwise contrary to applicable law, such provision shall be deemed restated to reflect as nearly as possible...
Search Results "Reflecting Surface"
Filters
Commonly Searched Documents
-
IMPLEMENTATION AND ENFORCEMENT
-
IMPLEMENTATION AND ENFORCEMENT
If any provision of this Agreement is determined to be invalid, unenforceable, or otherwise contrary to applicable law, such provision shall be deemed restated to reflect as nearly as possible...
-
IMPLEMENTATION AND ENFORCEMENT
If any provision of this Agreement is determined to be invalid, unenforceable, or otherwise contrary to applicable law, such provision shall be deemed restated to reflect as nearly as possible...
-
IMPLEMENTATION AND ENFORCEMENT
If any provision of this Agreement is determined to be invalid, unenforceable, or otherwise contrary to applicable law, such provision shall be deemed restated to reflect as nearly as possible...
-
I. The Disabilities Convention and U.S. Disability Rights Law
Each requirement is tempered by limitations that reflect the difficulty and costs of achieving accessibility....
-
Sections §§ 35.108(d)(1)(vii) and 36.105(d)(1)(vii)—Comparison of Individual’s Performance of Major Life Activity Usually Will Not Require Scientific, Medical, or Statistical Analysis
These rules of construction reflect Congress’s rejection of the demanding standards of proof imposed upon individuals with disabilities who tried to assert coverage under the ADA prior to...
-
Expert opinion on current literature
There is a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb (3-6) . ...
-
Taking Measurements
Taking Measurements Sloped Surfaces One way to measure slope is to use a 24-inch level with leveling bubble and a tape measure....
-
What was measured and why?
Often, an unstable surface, for example, may be perceived as very difficult because of the unstable footing, even though the individual does not have to exert him/herself....
-
Table of Contents
Assembly Areas F222 Dressing, Fitting, and Locker Rooms F223 Medical Care and Long-Term Care Facilities F224 Transient Lodging Guest Rooms F225 Storage F226 Dining Surfaces...
-
1009.5.4 Transfer Steps
The surface of the bottom tread shall extend to a water depth of 18 inches (455 mm) minimum below the stationary water level. Advisory 1009.5.4 Transfer Steps....
-
406.8 Detectable Warnings
width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum measured from the back of the curb on the ramp surface...
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
Tread Obstacles on Beach Access Routes
When the surface of the beach access route is paved or is built with boards, tread obstacles must not be more than a half of an inch (13 millimeters) high....
-
1018.5 Obstacles
Where the surface is other than concrete, asphalt, or boards, obstacles are permitted to not exceed 1 inch in height measured vertically to the highest point....
-
A7. Curb Ramps
Is the ramp surface at least 36” wide, excluding flared sides? [ADA Stds 4.7.3] Yes _____ No _____ b. Is the slope (up or down the ramp) no more than 1:12? ...
-
R308.1 Transit Stops
Transit stops should be located so that there is a level and stable surface for boarding vehicles....
-
Instrumentation for Analysis
Appendix C) was created to collect data on the 11 trail segments including Rotational Penetrometer readings, inspection location in feet from trailhead, ruts, tread obstacles, or other surface...
-
11B-812.7.2 Marking
The color of the borderlines, hatched lines, and letters shall contrast with that of the surface of the access aisle....
-
1018.2 Aisles in assembly spaces
for applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, shall also comply with Chapter 11A or Chapter 11B, Section 11B-403 _|Walking Surfaces...
-
Resting Intervals [1017.8]
When the surface of the resting interval is constructed of concrete, asphalt, or boards, the slope of the resting interval must be no steeper than 1:48 (2 percent) in any direction....
-
Dune Crossings [1018.10]
The handrails must be continuous at a height of 34 to 38 inches above the walking surface along both sides of the dune crossing (figure 32)....
-
New Construction
Dining and Work Surfaces -- Sections 226 and 902. The provisions regarding accessible routes in section 206.2.5 (Restaurants and Cafeterias) also apply to dining surfaces....
-
Technical Requirements for Accessible Hiker/Pedestrian Trails
Section 7.4 of FSTAG explains the accessibility requirements for trails, including trail surfacing, clear tread width, grade and cross slope, resting intervals, passing spaces, tread obstacles...