.-- Notwithstanding any other provision of this Act or of law, the purposes of this Act shall, subject to paragraphs (2) and (3), apply in their entirety to the House of Representatives....
Search Results "Grade 2 Braille"
-
12209(b)(1) In general
-
609.2.1 Circular Cross Section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
T301.1 Scope
The requirements in Chapter 3 shall apply where required by Chapter 2 or where otherwise referenced in any other chapter of the Non-Rail Vehicle Guidelines....
-
T701.1 Scope
The requirements in Chapter 7 shall apply where required by Chapter 2 or where otherwise referenced in any other chapter of the Non-Rail Vehicle Guidelines....
-
T401.1 Scope
The requirements in Chapter 4 shall apply where required by Chapter 2 or where otherwise referenced in any other chapter of the Non-Rail Vehicle Guidelines....
-
T501.1 Scope
The requirements in Chapter 5 shall apply where required by Chapter 2 or where otherwise referenced in any other chapter of the Non-Rail Vehicle Guidelines....
-
T601.1 Scope
The requirements in Chapter 6 shall apply where required by Chapter 2 or where otherwise referenced in any other chapter of the Non-Rail Vehicle Guidelines....
-
T303.3.2 Handrail and Stanchion Circular Cross Section
Handrails and stanchions with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (50 mm) maximum....
-
§8.57 Procedure for effecting compliance.
[53 FR 20233, June 2, 1988; 53 FR 28115, July 26, 1988, as amended at 72 FR 73491, Dec. 27, 2007]...
-
12186(a)(3) Standards
(3) Standards The regulations issued pursuant to this subsection shall include standards applicable to facilities and vehicles covered by sections 12182(b)(2) and 12184 of this title....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
10.2.2(1)
(1) Bus stop sites shall be chosen such that, to the maximum extent practicable, the areas where lifts or ramps are to be deployed comply with section 10.2.1(1) and (2)....
-
3.1.1.1 Vehicle Parking Lots
Vehicle parking lots with more than 2 parking spaces that are not associated with an individual camping or picnic unit shall comply with ABAAS sections 208 and 502....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
M303.3.3.4 Edge Protection
Ramps with drop offs ½ inch (13 mm) or greater shall provide edge protection 2 inches (50 mm) high minimum on each side....
-
DIRECTIONAL SIGN
[DSA-AC, HCD 1 & HCD 2]. A publicly displayed notice which indicates by use of words or symbols a recommended direction or route of travel....
-
§ 37.213(b)
(b) This paragraph (b) applies to small fixed route operators who choose to provide equivalent service to passengers with disabilities under §37.183(b)(2)....
-
§ 38.157(a)
(a) Any stepwell or doorway immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured on the step tread....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
DIRECTIONAL SIGN
[DSA-AC, HCD 1 & HCD 2]. A publicly displayed notice which indicates by use of words or symbols a recommended direction or route of travel....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
- Global Access Association