Operable parts shall be placed within one or more of the reach ranges specified in 308.
Search Results "Transfer Surface Height"
-
309.3 Height
-
4.27.3* HEIGHT
The highest operable part of all controls, dispensers, receptacles, and other operable equipment shall be placed within at least one of the reach ranges specified in 4.2.5 and 4.2.6....
-
4.25.3 HEIGHT
Accessible storage spaces shall be within at least one of the reach ranges specified in 4.2.5 and 4.2.6. Clothes rods shall be a maximum of 54 in (1370 mm) from the floor (see Fig....
-
Single-User Toilet Rooms: Side Transfer Space
Single-User Toilet Rooms: Side Transfer Space These drawings illustrate the space requirements for a single-user toilet room with a single plumbing wall....
-
Bradley Security Grab Bars Model SA70 Series
Requires the Premium User plan or above. (Login or upgrade your account!) -
What surface characteristics are required of an accessible route?
What surface characteristics are required of an accessible route?...
-
Side guard protocol
Side guard protocol: From initial setup, two side guards adjusted 6” (15.2 cm) higher than the subject’s WMD seat were attached, and subjects were asked to perform a level height transfer...
-
11B-809.8 Doors
between floor surfaces....
-
Grainger Tough Guy Stainless Steel Sanitary Napkin Receptacle, 11" Height
Stainless Steel Sanitary Napkin Receptacle, 11" Height, 1 EA Item# 1ECK9 Mfr....
-
#CrappyCurb
Cities Should Be Built for Everybody “Crappy Curbs” are sidewalk curbs that don’t include ramps. This makes getting around the city for people with mobility disabilities...
-
Caroma® USA Somerton Smart 270 Easy Height Elongated Toilet
A modern concept close coupled 1.28/0.8 gpf (4.8/3 lpf), Somerton Smart 270 Easy Height Elongated dual flush washdown toilet installation designed to provide a seat height of between 17”...
-
Curb Ramp Requirements [§406]
Curb Ramp Requirements [§406]
-
1011.5.2 Riser height and tread depth
... Exceptions: 4. ... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Section...
-
1011.5.2 Riser height and tread depth
... Exceptions: 4. ... [DSA-AC] For applications listed in Section 1.9.1 regulated by the Division of the State Architect-Access Compliance, see Chapter 11B, Section...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
R305 Detectable Warning Surfaces (Section-by-Section Analysis) Detectable warning surfaces consist of truncated domes aligned in a square or radial grid pattern....
-
SUMMARY OF THE 19-INCH RECOMMENDATION
Access Board’s Medical Diagnostic Equipment Technical Advisory Committee discussed transfer surface height extensively....
-
R208 Detectable Warning Surfaces (Section-by-Section Analysis)
R208 Detectable Warning Surfaces (Section-by-Section Analysis) Detectable warning surfaces consist of small truncated domes built in or applied to a walking surface that are detectable...
-
Caroma® USA Sydney Low Profile 270 Easy Height Elongated Toilet
A modern concept close coupled 1.6/0.8 gpf (6/3 l) Sydney Low Profile 270 Easy Height Elongated dual flush high efficiency toilet (HET) designed to provide a seat height of between 17" to...
-
DSA IR 11B-7 REQUIREMENTS FOR ACCESSIBLE PARKING SPACES (with revisions issued through Jan. 2011)
Acceptable Designs: Asphalt is often the parking surface material used at accessible parking spaces. Asphalt is generally considered to be fairly dark in appearance....
-
Lateral grab bar use
It can be noted that the lateral grab bar is used by more subjects when the transfer setup increases in level of difficulty (i.e. gap/height in combination or side guard)....
-
Expert opinion on current literature
There is a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb (3-6) . ...
-
Providing Appropriate Information About Accessibility
For instance, include minimum width, maximum slope, and condition of the tread surface (is it firm and stable?) on information about trails....
-
11B-903.4 Back support
surface....
