The height of the operable part shall conform to Table 407.8.3.2.1....
Search Results "Transfer Surface Height"
-
407.8.3.2.1 Operable Part Height for ICT with Obstructed Forward Reach
-
American Standard Yorkville 1.1 gpf FloWise Right Height Elongated Pressure Assisted Toilet
Connect® tank/bowl coupling system 4 bolt caps Sanitary bar on bowl Recommended working pressure range 25 psi - 80 psi Specs Dimensions Height...
-
Bobrick TrimLine Series ADA Surface-Mounted Hand Dryer B-7120.115V Informational Video
Bobrick TrimLine Series ADA Surface-Mounted Hand Dryer B-7120.115V Informational Video...
-
Lift Compatibility (M301.4 and M302.4)
supine, prone, or sidelying position, and diagnostic equipment used by patients in a seated position to be usable with a patient lift for patients with disabilities for whom independent transfer...
-
American Standard Cadet 1.1 gpf FloWise Right Height Pressure Assisted Elongated Toilet 2467136
Elongated bowl Pressure-assisted siphon jet flush action 16-1/2" rim height for accessible applicatons Fully glazed 2-1/8" trapway 10" x 12" water...
-
Access-Able Designs Tub Transfer Bench SH-414-LR
Rests on tub wall to allow 17-19" height. Folds up easily when not in use. Available with phenolic tops....
-
1136A.1 Receptacle heights
Baseboard electrical outlets used in relocatable partitions, window walls or other electrical convenience floor outlets are not subject to the minimum height requirements....
-
SECTION 1136A ELECTRICAL RECEPTACLE, SWITCH AND CONTROL HEIGHTS
SECTION 1136A ELECTRICAL RECEPTACLE, SWITCH AND CONTROL HEIGHTS...
-
5.8.2.6 Clearance Depth at Toe Height above the ground Recommendation
5.8.2.6 Clearance Depth at Toe Height above the ground Recommendation The Committee recommends 22 inches minimum clearance depth at toe height....
-
Accessible Routes Adjacent to the Playing Surface
Accessible Routes Adjacent to the Playing Surface If the accessible route is adjacent to the playing surface, it must not exceed 36 inches from any area where golf balls rest....
-
1136A.1 Receptacle heights
Baseboard electrical outlets used in relocatable partitions, window walls or other electrical convenience floor outlets are not subject to the minimum height requirements. 4....
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? ...
-
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations
5.8.1.2.4 Edge Protection on Platforms 1½ inches or less in Height Recommendations The Committee recommends that no edge protection be required on platforms of 1½ inches or less in height...
-
Armor-Tile Tactile Systems Surface Applied Systems Installation Video
This is a video demonstrating how to install a single Armor Tile surface-applied tile....
-
8.4 Improving Data Sources and Research
For example, the Committee was making recommendations about standards for transfer surfaces of certain sizes....
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
11B-812.9 Surface marking
EVCS vehicle spaces shall provide surface marking stating “EV CHARGING ONLY” in letters 12 inches (305 mm) high minimum....
-
Attachment I: Program Access in Existing Facilities
Attachment I: Program Access in Existing Facilities
-
ETA Summary of ADAAG/CBC Signage Requirements
ADAAG/CBC Signage Requirements Click here to view/download the pdf version (1.22 MB)
-
ETA Summary of ADA Signage Requirements
Summary of ADA Signage Requirements Click here to view/download the pdf version (162 KB).
-
Notes
Analysis of Seat Height for Wheeled Mobility Devices. 2011. 3. The Impact of Transfer Setup on the Performance of Independent Transfers: Final Report....
-
I. Introduction
The purpose of this Minority Report is to make a formal recommendation for a minimum transfer surface low height of 19 inches for diagnostic imaging medical equipment....
