Section 234.4.2 covers the most current ADA scoping requirements for the minimum number of wheelchairs spaces, transfer seats or devices at existing amusement rides.
Search Results "Transfer Surface Height"
-
Minimum Number: ADA Standard Section 234.4.2
-
Why a smooth surface door or kickplate is important
Remember that the latch that hits the push rim is nicking the surface your fingers have to grasp thousands of times a day for years....
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
11B-611.4 Height
FIGURE 11B-611.4 HEIGHT OF LAUNDRY COMPARTMENT OPENING...
-
Objective Surface Measurements
Objective Surface Measurements For purposes of comparison, objective surface measurement data are included from the “Measurement of Surface Characteristics for Accessibility” NIH-funded...
-
What other surface considerations affect wheelchair travel?
What other surface considerations affect wheelchair travel?...
-
4.34.5.5 SHOWERS
If a shower is provided, it shall have the following features:
-
Section A: Parking
(§502.5) A4 Are designated accessible parking spaces and the access aisles serving them on a level surface, with slopes not exceeding 1:48 in all...
-
36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
Published in the Federal Register on January 9, 2017. RIN 3014-AA40 AGENCY: Architectural and Transportation Barriers Compliance Board. ACTION: Final rule. SUMMARY: The...
-
36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
Published in the Federal Register on January 9, 2017. 36 CFR Part 1195 RIN 3014-AA40 Standards for Accessible Medical Diagnostic Equipment AGENCY: Architectural and...
-
Example 1: With Cooking Facilities
With Cooking Facilities An employee break room with fixed or built-in range cooking facilities shall comply with the requirements of 212 and 804 for kitchens and kitchenettes....
-
3.3.7 Toe Clearance Height, minimum
3.3.7 Toe Clearance Height, minimum There is relatively large disparity between the standards for toe clearance height, with the U.S. having the lowest (230 mm or 9 in.), followed by...
-
2. Analysis of footrest clearance height and depth
Detailed footrest measurements (i.e., foot rest height and corner points on the top surface) were collected from 158 manual wheelchair users and 108 power wheelchair users....
-
709.8 Duct and air transfer openings
Penetrations by duct and air transfer openings shall comply with Sections 711 and 715....
-
What is a good un-official "working" definition of "work surface"?
11B-805.7 goes on to list numerous items that would/could be included in the broad verbiage of "Built-in cabinets, counters and work surfaces"....
-
Front grab bar protocol
and 2) transferring to higher heights than their WMD seat height. ...
-
AN INCREASING NUMBER OF HEALTH CARE PROVIDERS ARE TRANSITIONING TO ADJUSTABLE HEIGHT TABLES
-inch low height.19 This is a significant increase over the 17 percent of adjustable height tables sold in 2005....
-
Comfort Designs Tamper Proof Anti-ligature Grab Bars
Tamper proof anti-ligature grab bars are designed to prevent tying of materials by eliminating space between wall and bar. Weep holes allow for water...
-
3.3.2 Experienced Clinicians
Committee members are deliberating how wide the portion of an exam table surface onto which patients transfer must be (defined as a “transfer surface”)....
-
3.3.6 Knee Clearance Height, minimum
3.3.6 Knee Clearance Height, minimum Knee clearance heights for the four sets of standards range from 650 mm (25.6 in.) (Australia) to 700 mm (27.6 in.) (U.K.) (Figure 3‒6)....
-
711.3.3 Ducts and air transfer openings
Penetrations of fire-resistance-rated walls by ducts and air transfer openings that are not protected with fire dampers shall comply with this section....
