The Access Board has divided the MDE Standards into separate technical criteria based on how the diagnostic equipment is used by the patient: (1) supine, prone, or side lying position (M301...
Search Results "Latch Side Clearance"
-
B. Summary of Major Provisions and Organization of Technical Criteria
-
G. Sleeping Areas
An accessible route is needed to provide access to each accessible cot and a clear space at least 36 inches wide is needed along the side of the cot to make it possible to transfer between...
-
E. Restaurants and Concessions:
PSE shall ensure that all moveable service counters provide service at the side of the stand....
-
Smooth Surface
Section 404.2.10 requires that swinging doors and gates have a smooth surface on the push side that extends their full width....
-
11B-406.5.3 Landings
The landing clear width shall be at least as wide as the curb ramp, excluding any flared sides, or the blended transition leading to the landing....
-
11B-604.5.2 Rear wall
The rear wall grab bar shall be 36 inches (914 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
11B-604.5.2 Rear wall
The rear wall grab bar shall be 36 inches (914 mm) long minimum and extend from the centerline of the water closet 12 inches (305 mm) minimum on one side and 24 inches (610 mm) minimum on...
-
Access-Able Designs Wall Mounted Shower Transfer Bench SH-400
Left or right sided tops. Measures 32" W x 21" D x 15" D. Custom sizes available. Must have adequate wall backing. Folds up easily when not in use....
-
Horton Automatics EasyAccess® Series 7100 for ADA Low Energy Applications
Americans With Disabilities Act of 1990 Standard system features & benefits: Heavy duty motor designed for standard accessibility applications Surface mount 4" x 6" side...
-
Guidelines for Requirement 5
The inclusion of this additional specification for side approach is consistent with the comparable provisions in the ANSI Standard....
-
Just Manufacturing Ledgemount Non-Swivel Gooseneck Concealed Mixing Faucet
Rigid gooseneck spout with 7-3/8" clearance. Replaceable seats. Brass quarter turn quick compression stem units....
-
11B-610.3.1 Rectangular seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. FIGURE 11B-610.3.1 RECTANGULAR SHOWER SEAT...
-
608.3.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
610.3.1 Rectangular Seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. Figure 610.3.1 Rectangular Shower Seat...
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
-
4.7.7 Water Spouts
Water spouts shall be located in the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum from the rear center of the long side of the clear floor or...
-
Is color contrast required for stair nosings?
The ASME A17.1 code requires escalator steps to be demarcated by yellow lines 2” wide maximum along the back and sides....
-
11B-608.3.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
11B-608.5.1 Transfer type shower compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1219 mm...
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
-
608.5.1 Transfer Type Shower Compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm...
-
802.1.3 Depth
Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
PULL: CTC: 8" Projection: 3" Clearance: 2" PUSH: Projection: 2-1/2" Clearance: 1-1/2" WEIGHT: 11.5 lbs....
