In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
Search Results "Latch Side Clearance"
-
608.3.3 Alternate Roll-In Type Shower Compartments
-
610.3.1 Rectangular Seats
The side edge of the seat shall be 1½ inches (38 mm) maximum from the adjacent wall. Figure 610.3.1 Rectangular Shower Seat...
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
-
4.7.7 Water Spouts
Water spouts shall be located in the space so that the water spout is 11 inches (280 mm) minimum and 12 inches (305 mm) maximum from the rear center of the long side of the clear floor or...
-
Is color contrast required for stair nosings?
The ASME A17.1 code requires escalator steps to be demarcated by yellow lines 2” wide maximum along the back and sides....
-
11B-608.3.3 Alternate roll-in type shower compartments
In alternate roll-in type shower compartments, grab bars shall be provided on the back wall and the side wall farthest from the compartment entry....
-
11B-604.9.5 Flush controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with Section 11B-604.8.2....
-
11B-608.5.1 Transfer type shower compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1219 mm...
-
11B-602.3 Operable parts
The flow of water shall be activated by a manually operated system that is front mounted or side mounted and located within 6 inches (152 mm) of the front edge of the fountain or an automatic...
-
608.5.1 Transfer Type Shower Compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1220 mm...
-
802.1.3 Depth
Where a wheelchair space can be entered only from the side, the wheelchair space shall be 60 inches (1525 mm) deep minimum....
-
Cal-Royal Products Grade 1 Cylindrical Lockset Calypso CAL Series
LATCH FACEPLATE - 2 1/4" x 1 1/8" adjustable for flat or beveled doors 1/8" in 2", for 2 3/4" backset. Optional 2 1/4" x 1 1/8" for 2 3/8" backset....
-
TownSteel ED1300 Grade 1 Concealed Vertical Rod Panic Device
Thickness 1-3/4"-2-1/4" Door Width 36" device for up to 3' wide and 7' high openings, 48" device for up to 4' wide and 8' high openings Operation Pressing push bar retracts top and bottom latch...
-
California: Toilet Grab Bars - Uneven height allowed?
I noticed that the specific code language suggests that the side grab bar and the rear grab bar must be at the same height (California CBC text is slightly different than ADAS), but it reads...
-
Bobrick Partition-Mounted Multi-Roll Toilet Tissue Dispenser (Serves 2 Compartments) B-386
Mounts centered through toilet partitions, 1/2–2" (12–50mm) thick; used from both sides. Holds four standard core toilet tissue rolls up to 5 1/8" (130mm) diameter; two for each side....
-
Rulemaking Authority
They’re going to look at the knee and toe clearances that our guidelines establish in order to determine whether or not the table is generally useable to individuals who use wheelchairs....
-
Minimum Clear Opening
Representatives Edwards, Frank, and Fish expressed their support for the Option One specification on minimum clearance which is consistent with the ANSI Standard....
-
11B-809.10.6.1 Size
11B-809.10.6.1 or; A shower stall 36 inches (914 mm) deep by 60 inches (1524 mm) wide minimum with an entrance 36 inches (914 mm) minimum when a wall is installed on the opening side...
-
Behavioral Safety Products #DH410 Cylindrical Ligature Resistant Lever Handle
This ligature resistant cylindrical latch set meets ADA standards by eliminating the operational requirement "pinch and grasp motion". ...
-
Stabila slope meter is easy to read
I like this slope meter because of the readings provided on the top and the side of the slope meter. Makes documentation with photos very easy in the field....
-
11B-404.2.9 Door and gate opening force
These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position....
-
11B-404.2.9 Door and gate opening force
These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position....
-
11B-404.2.9 Door and gate opening force
These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position....
-
Section 37.9 Standards for Transportation Facilities
One further clarification concerning the implication of this provision deals with a bus loading island at which buses pull up on both sides of the island....
