Section 603 covers the current ADA Standards for toilet and bathing rooms.
Search Results "Shower Room"
Commonly Searched Documents
-
Toilet and Bathing Rooms: ADA Standard Section 603
-
4.8 Outdoor Rinsing Showers
[See subsections ...]
-
608.5 Controls
Controls, faucets, and shower spray units shall comply with 309.4....
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall. The side edge...
-
Bathroom Do’s and Dont’s
Provide a rubber shower mat as an option....
-
Coat Hooks and Shelves: ADA Standard Section 803.5
Coat hooks provided within the room shall be located within one of the reach ranges specified in 308....
-
4. Shower Wand
Is there an adjustable height hand-held shower wand with at least a 60" long hose provided so persons who bathe from a seated position may wash and rinse with the directional spray?...
-
Location of Controls
Comments indicated that this specification was not consistent with a corresponding figure showing the location on the side closest to the shower opening. Response....
-
11B-608.2.1 Reserved
ETA Editor's Note The transfer type shower compartments prescribed by 2010 ADAS 608.2.1 are not recognized as an accessible shower in California....
-
Toilet Rooms and Bathing Rooms: ADA Standard Section 216.8
Section 216.8 covers scoping requirements in the current ADA Standards for signs at toilet rooms and bathing rooms.
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-608.2.3 Alternate roll-in type shower compartments
11B-608.2.3 Alternate roll-in type shower compartments....
-
11B-612 Saunas and steam rooms
[See subsections ...]
-
11B-603 Toilet and bathing rooms
[See subsections ...]
-
11B-809.10.6.4 Reinforcement for grab bars
Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
Dressing, Fitting, or Locker Rooms
Dressing, Fitting, or Locker Rooms When provided, dressing, fitting, or locker rooms must be accessible and comply with all ADAAG provisions....
-
Minimum Number [9.1.2 and 9.1.3]
Rooms with combination roll-in/transfer showers are required in transient lodging facilities with more than 50 rooms....
-
4.21.7 Curbs
All of the designs reviewed were curbless, roll-in showers....
-
Guest Rooms with Mobility Features: ADA Standard Section 806.2
Guest rooms required to provide mobility features shall comply with 806.2. Advisory 806.2 Guest Rooms....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-216.8 Toilet rooms and bathing rooms
Where existing toilet rooms or bathing rooms do not comply with Section 11B-603, directional signs indicating the location of the nearest toilet room or bathing room complying with Section...
- Wisconsin Bench Manufacturing ADA Locker Benches
-
608 Shower Compartments
[See subsections ...]