Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
705.1.1 Dome Size
-
Re: How important is the UX process when building a new product?
A structured user experience approach is essential because it validates ideas before expensive development begins....
-
C. M303 Diagnostic Equipment Used by Patients Seated in a Wheelchair
M303 contains the technical requirements for diagnostic equipment used by patients seated in wheelchairs....
-
12185(c)(3)
(3) members selected for their technical expertise on issues included in the study, including manufacturers of boarding assistance equipment and devices....
-
1018.9 Protruding Objects
This section requires constructed elements on beach access routes and resting intervals to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers...
-
11B-208.2 Minimum number
The term "parking facility" is used in 208.2 instead of the term "parking lot" so that it is clear that both parking lots and parking structures are required to comply with this section....
-
11B-208.2 Minimum number
The term "parking facility" is used in 208.2 instead of the term "parking lot" so that it is clear that both parking lots and parking structures are required to comply with this section....
-
11B-809.10.7.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from a wall or partition that is 54 inches (1372 mm) minimum in length....
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
11B-809.10.7.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from a wall or partition that is 54 inches (1372 mm) minimum in length....
-
1607A.9.2 Grab bars, shower seats and accessible benches
designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar, shower seat, or seat of the accessible bench so as to produce the maximum...
-
11B-407.4.10.1 Location
Top of support rails shall be 31 inches (787 mm) minimum to 33 inches (838 mm) maximum above the floor of the car....
-
11B-309.4 Operation
The force required to activate operable parts shall be 5 pounds (22.2 N) maximum....
-
309.4 Operation
The force required to activate operable parts shall be 5 pounds (22.2 N) maximum....
-
Transfer Steps
Transfer Steps The maximum height of transfer steps is 8 inches, although shorter heights are recommended....
-
804.3.2 Height
The kitchen work surface shall be 34 inches (865 mm) maximum above the finish floor or ground....
-
R304.3.2 Running Slope
The running slope of the curb ramp shall be 5 percent minimum and 8.3 percent maximum but shall not require the ramp length to exceed 4.5 m (15.0 ft) minimum....
-
309.4 Operation
The force required to activate operable parts shall be 5 pounds (22.2 N) maximum....
-
309.4 Operation
The force required to activate operable parts shall be 5 pounds (22.2 N) maximum....
-
1132A.4, Item 4
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 1 inch (25.4 mm), provided a ramp with a maximum slope of 1:8 is permanently installed....
-
11B-407.4.10.1 Location
Top of support rails shall be 31 inches (787 mm) minimum to 33 inches (838 mm) maximum above the floor of the car....
-
11B-407.4.10.1 Location
Top of support rails shall be 31 inches (787 mm) minimum to 33 inches (838 mm) maximum above the floor of the car....
-
11B-611.4 Height
Top loading machines shall have the door to the laundry compartment located 36 inches (914 mm) maximum above the finish floor....
-
309.4 Operation
The force required to activate operable parts shall be 5 pounds (22.2 N) maximum....