(iii) Outside the core service area, the entity may designate corridors with widths from three-fourths of a mile up to one and one half miles on each side of a fixed route, based on local...
Search Results "Latch Side Clearance"
-
§ 37.131(a)(1)(iii)
-
Portable Units [4.1.2(6)]
Where ramps are provided, it is important that required door clearances are available at the required level landing....
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-2620
Door has knob-latch and piano-hinge. Hemmed towel tray opening. Unit 10 3/4" W, 14" H, 4" D (275 x 355 x 100mm)....
-
Bobrick ClassicSeries Surface-Mounted Paper Towel Dispenser B-2621
Door has knob-latch. Hemmed towel tray opening. Unit 10 3/4" W, 7 1/8" H, 4" D (275 x 180 x 100mm)....
-
31.1 Q. Can a water closet (toilet) be located in an alcove with a wing wall?
This would mean that the wing wall could not extend beyond the front edge of a lavatory located on the other side of the wall from the water closet....
-
604.6 Flush Controls
Flush controls shall be located on the open side of the water closet except in ambulatory accessible compartments complying with 604.8.2....
-
607.5 Controls
Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub. Controls shall comply with 309.4....
-
602 Drinking Fountains
Substantive changes to this section include: removal of references to water coolers (602.1) requiring all wheelchair accessible drinking fountains to provide knee and toe clearance...
-
Footrests and Armrests
This clearance is needed for people transferring between the lift and a mobility device....
-
Wheelchair Passage Width [4.2.1] and Passing Space [4.2.2]
Additional clearance is needed for maneuvering and sway....
-
Standing Supports (M304.3 and M305.3)
M304.3 would require standing supports to be provided on each side of the standing surface on diagnostic equipment used by patients in a standing position....
-
BEST Door Lever Hardware Cylindrical Locks - 7KC
Standard and Drive-in latches available. Through-bolt mounting studs increase torque resistance. Quick rekeying with BEST interchangeable core....
-
Yale 1100 Series Industrial Door Closer
The 1100 series features rugged construction, adjustments for closing and latch speed, and rack and pinion operation....
-
Cal-Royal Legacy Series Locksets
Push button releae on entrance & privacy from inside by turning lever 2-3/8" or 2-3/4" 4-way adjustable backset, size 1" x 2-1/4" round corner standard, convertible to drive in latch...
-
Yale 2700 Series Architectural Door Closer
The 2700 series features rugged construction, adjustments for backcheck, closing and latch speed, rack and pinion operation and a variety of arm options....
-
Direct Access Solutions Kit
after using the restroom Hanging up their clothes in a standard closet Adjusting the thermostat to a comfortable temperature Locking and unlocking the security latch...
-
K4
, drink, condiment, and tableware dispensers are provided, are dispensers and operating controls mounted no higher than 54 inches above the floor if clear floor space is provided for a side...
-
Jamb Signage
...are all elevator jambs provided with signs placed on both sides designating the floor with 2" minimum height raised letters and Braille characters centered at 60" above the finish floor...
-
I1a
For a side approach (clear floor space at least 30 inches long x 48 inches wide), is the coin slot no higher than 54 inches above the floor?...
-
5e.
Are signs mounted on both sides of the elevator hoistway door opening that designate the floor with 2-inch minimum-height raised letters and Braille characters centered at 60 inches above...
-
Assembly Areas
where they adjoin seating and since accessible routes are required to connect to wheelchair seating locations, compliance with 4.9, including requirements for handrails, is not required at sides...
-
4.34.5.5(4) Controls
In the shower stall in Fig. 35(a), all controls, faucets, and the shower unit shall be mounted on the side wall opposite the seat....
-
Inclusion Solutions Voting Booth Accessories Franklin Voting Chair
Compatible with all accessible voting systems and voting booths. 23.25” chair width is optimal dimension to fit under 32” required minimal ADA clearance space under voting booths...
-
4.3.3 Clear Floor Area
The clear floor area width also informs the minimum clearance width for successful passage through corridors, doorways and ramps....
