The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
Search Results "Latch Side Clearance"
-
Curb Ramps at Marked Crossings and Vehicular Lanes
-
M302.3.1 Transfer Supports (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that transfer supports must be provided for use with transfer sides on diagnostic equipment used by patients in the seated position, and that these...
-
Norton Surface Mounted Medium Duty 8000 Series Door Closer
Bi-pack packaging standard (regular arm and top jamb mounting) Exceeds 10 million cycles (witnessed and verified by UL) Non-handed Staked valves Standard, separate and independent, latch...
-
A6
If a curb ramp is provided, is the running slope of the ramp surface (not counting the side flares) no more than 1:12 or 8.33% [ADA Standards § 4.7.2] Yes No...
-
4.9.4(1)
(1) Handrails shall be continuous along both sides of stairs. The inside handrail on switchback or dogleg stairs shall always be continuous (see Fig. 19(a) and (b))....
-
Handrails [4.9.4]
Continuous handrails are required along both sides of stairs. A center rail is not specified for wide stairways by ADAAG but may be required by local building or life safety codes....
-
§ 38.23(c)(4) Ramp barriers
Each side of the ramp shall have barriers at least 2 inches high to prevent mobility aid wheels from slipping off....
-
GUARD [DSA-AC, HCD 1, HCD 2 & HCD 1-AC] OR GUARDRAIL
A building component or a system of building components located at or near the open sides of elevated walking surfaces that minimizes the possibility of a fall from the walking surface to...
-
305.6 Approach
One full unobstructed side of the clear floor or ground space shall adjoin an accessible route or adjoin another clear floor or ground space....
-
804.6.5.2 Bottom-Hinged Door Ovens
Bottom-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to one side of the door....
-
4.3.5.1 90-Degree Turn
4.3.5.1 90-Degree Turn This turning clearance is applicable for exterior and interior circulation, aisles in seating areas, ramps and other locations....
-
Introduction
Objects that project into circulation spaces from the side or that do not provide at least 80 inches of head clearance can be extremely hazardous to people who are blind or who have low...
-
Roundabouts (Section-by-Section Analysis)
Pedestrian street crossings at roundabouts can be difficult for pedestrians who are blind or have low vision to identify because the crossings are located off to the side of the pedestrian...
-
704.5 TTY Shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (150 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
11B-308.4 Suggested reach ranges for children
These dimensions apply to either forward or side reaches....
-
907.2.6.1 Group I-2
Such detectors shall provide a visual display on the corridor side of each patient room and shall provide an audible and visual alarm at the nursing station attending each room....
-
Safe Harbor – Construction Prior to March 15, 2012
For example, the 1991 Standards allow 54 inches maximum for a side reach range to a control such as the operating part of a paper towel dispenser....
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-308.4 Suggested reach ranges for children
These dimensions apply to either forward or side reaches....
-
M303.3.3.4 Edge Protection
Ramps with drop offs ½ inch (13 mm) or greater shall provide edge protection 2 inches (50 mm) high minimum on each side with a drop off....
-
R304.5.1 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
407.8.1 Vertical Reference Plane
Operable parts shall be positioned for a side reach or a forward reach determined with respect to a vertical reference plane....
-
5c.
Are the highest floor control buttons in the elevator cab mounted no more than 54 inches above the floor for a side reach or 48 inches for forward reach? Yes _____ No _____...
