The 40 1/2" height of the main ticket counter exceeds the maximum allowable height of 36" above the finished floor. See Standards § 7.2(1). j....
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
Main Lobby
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
11B-605.4 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except that the flush control shall be mounted at a maximum height of 44 inches (1118 mm) above the finish floor....
-
7.4.5 Passing Spaces
Trails with a clear tread width less than 60 inches (1525 mm) shall provide passing spaces complying with 7.4.5 at intervals of 1000 feet (300 m) maximum. ...
-
10.3.1(6)
All signs referenced in this paragraph shall, to the maximum extent practicable, be placed in uniform locations within the transit system....
-
10.3.2(5)
(5) New direct connections to commercial, retail, or residential facilities shall, to the maximum extent feasible, have an accessible route complying with 4.3 from the point of connection...
-
10.3.1(15)
Clocks shall be placed in uniform locations throughout the facility and system to the maximum extent practicable....
-
Sales Counters [7.2(1)]
(ADAAG does not specify maximum travel distances)....
-
10.4.1(7)
Clocks shall be placed in uniform locations throughout the facility to the maximum extent practicable....
-
Vertical Wheelchair Lifts
The ASME code specifies a maximum travel distance of 12 feet and prohibits penetration of floors....
-
1.1.4
1.1.4 A maximum overall design running slope for exterior accessible ramps of 7.5% (1:13.3 or 1:13) is recommended....
-
11B-604.9.5 Flush controls
Hand operated flush controls shall comply with Sections 11B-309.2 and 11B-309.4 and shall be installed 36 inches (914 mm) maximum above the finish floor....
-
§ 37.153(c)(3)
to coordinate with other available providers of demand responsive service in the area served by the public entity to maximize the service to ADA paratransit eligible individuals to the maximum...
-
11B-239.2 Minimum number
If a course is designed with the minimum 50 percent accessible holes, designers or operators are encouraged to select holes which provide for an equivalent experience to the maximum extent...
-
11B-239.2 Minimum number
If a course is designed with the minimum 50 percent accessible holes, designers or operators are encouraged to select holes which provide for an equivalent experience to the maximum extent...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-604.6 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except they shall be located 44 inches (1118 mm) maximum above the floor....
-
(1) Adjustability: Minimum High Transfer Height
recommended increasing the minimum high height to 28 inches for all diagnostic equipment except magnetic resonance imaging (MRI) equipment, which has limitations that may prevent it from reaching...
-
C204.1 General (Section-by-Section Analysis)
Similarly, these types of products do not typically provide transactional outputs covered by proposed 409. 407.12 Reach Height and 408 Display Screens....
-
B. Question 2: Section 904.4.1 and Clear Counter Space
Section 904.2’s Advisory further directs that, when a cash register is set on a sales or service counter, it should be located where people with disabilities can reach the cash register...
-
DEFENDANTS’ RAISED PORCHES
From atop the raised porches, the interior of the store is reached by proceeding through an opening without a door and descending two steps. See Order 3, ECF No. 109. ...
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
11B-404.2.7 Door and gate hardware
Operable parts of such hardware shall be 34 inches (864 mm) minimum and 44 inches (1118 mm) maximum above the finish floor or ground....
-
Data Analysis
The 5th, 25th, 50th, 75th, and 95th percentiles were recorded along with the minimum and maximum heights attained for each part of each protocol....