deviation of 3mm in 3m, Class B has a maximum deviation of 6mm in 3m, and a Class C has a maximum deviation of 6 mm in 600 mm....
Search Results "Maximum Reach Depth"
Filters
Commonly Searched Documents
-
Standards
-
DORMA KTC-2 Revolving Door
As soon as the door has reached this position, the center section may be opened manually in order to create an escape route....
-
Delta Single Handle Pull-Down Kitchen Faucet with Touch2O Technology 9197T-DST
build-up 1 or 3-hole installation For 3-hole installation, order escutcheon RP71545 High-arc pull-down swivels 360 for complete sink access 62 in. long hose provides outstanding reach...
-
Pilot Rock FSWDW-30 Campfire Ring
This Swivel Grate meets the ADA guidelines for reach and operability. Inside is the large 380 sq. inch log grate. ...
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
Shower Spray Unit
Comments also noted that delivered water should be "temperature limited" to the specified maximum (120 degrees) for consistency with American Society of Safety Engineers (ASSE) standards...
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
2.3.4 Analysis of Door Use Difficulty
The mean, median and range of WhMD user age, occupied width, occupied length and maximum power grip were also reported as we thought that these variables might help explain the door use...
-
4.26.3 STRUCTURAL STRENGTH
structural strength of grab bars, tub and shower seats, fasteners, and mounting devices shall meet the following specification: (1) Bending stress in a grab bar or seat induced by the maximum...
-
11B-1008.2.5.2 Elevated
The rise for any ramp run connecting elevated play components shall be 12 inches (305 mm) maximum....
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
407.4.8.2.1 Signal Type
EXCEPTION: For elevators other than destination-oriented elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum...
-
§8.6(c)
result in such an alteration or burdens, the recipient shall take any other action that would not result in such an alteration or such burdens but would nevertheless ensure that, to the maximum...
-
407.4.8.2.1 Signal Type
EXCEPTION: For elevators other than destination-oriented elevators that have a rated speed of 200 feet per minute (1 m/s) or less, a non-verbal audible signal with a frequency of 1500 Hz maximum...
-
11B-405.3 Cross slope
Curved ramps are not prohibited by Chapter 11B; however, requirements for maximum slope and cross-slope cannot be exceeded. ◼...
-
4.34.6.5(1)
(1) The sink and surrounding counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable...
-
Handrails [§504.6, §505]
Stairway Handrails Recommendation: In facilities that primarily serve children, a second set of stairway handrails 28” high maximum above stair nosings is advisable....
-
1.1.3 Walk running slope
Measure for overall running slope (the primary direction of travel) by determining elevations at the ends of the walk, noticeable changes in slope, or at a maximum of 20 ft (6 m) intervals...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
11B-812.7.2 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center....
-
11B-405.3 Cross slope
Curved ramps are not prohibited by Chapter 11B; however, requirements for maximum slope and cross-slope cannot be exceeded.◼...
