The surface of trails, passing spaces, and resting intervals shall be firm and stable. Advisory 1017.2 Surface. A firm trail surface resists deformation by indentations....
Search Results "Recreational Surfacing"
Filters
Commonly Searched Documents
-
1017.2 Surface
-
403 Walking Surfaces
The requirements for walking surfaces derive from existing specifications for accessible routes covering floor or ground surfaces, slope, changes in level, and clearances....
-
Floor Surfaces: ADA Standard Section 408.4.2
Section 408.4.2 covers the current ADA Standards for the floor surfaces of limited-use/limited-application elevators.
-
Site Profiles by Surface Type
Some playground sites were surfaced with one surface material/system while others were surfaced with a combination of two surface materials/systems. ...
-
Exposed Pipes and Surfaces: ADA Standard Section 606.5
Section 606.5 covers the current ADA Standards for exposed pipes and surfaces under lavatories and sinks.
-
Inclusion in Every Play
On February 24, 2015, the Commit to Inclusion campaign was highlighted at the “Inclusion in Every Play” bridge event between the National Physical Activity Plan Congress and the...
-
Kitchen Work Surface: ADA Standard Section 804.3
In residential dwelling units required to comply with 809, at least one 30 inches (760 mm) wide minimum section of counter shall provide a kitchen work surface that complies with 804.3....
-
11B-802.1.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
11B-802.1.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
Suggested accessibility guidelines for exterior concrete surfaces
The following tolerances may be applicable for exterior accessible surfaces....
-
403 Walking Surfaces
403 Walking Surfaces...
-
5.3.2.2 Surface
The surface of the turning space and clear floor or ground space shall be firm and stable. ...
-
304.2 Floor or Ground Surfaces
304.2 Floor or Ground Surfaces. Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
4.7.4 Surface
The surface of the clear floor or ground spaces required by section 4.0 shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
4.8.6 Cross Slope and Surfaces
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.8.6 CROSS SLOPE AND SURFACES
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.5.4 Surface
The surface of the clear floor or ground space for trash, recycling, and other essential containers shall be firm and stable....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
F244.2.3.2.1 Recreational Vehicles
Where parking spaces are provided for recreational vehicles, at least one parking space shall comply with 1012.2, 1012.4, and 1012.5....
-
7.4.1 Surface
The trail tread surface, including resting intervals and passing spaces, shall be both firm and stable....
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception. ...
-
Selection of Trail Surface Materials
Selection of Trail Surface Materials A review of trail surfacing products conducted for this project identified approximately 80 different trail surface materials that promoted providing...
-
R302.7.2 Vertical Surface Discontinuities
R302.7.2 Vertical Surface Discontinuities. Vertical surface discontinuities shall be 13 mm (0.5 in) maximum....