Section 238.3 covers scoping requirements in the ADA Standards for practice putting greens, practice teeing grounds, and teeing stations at driving ranges.
Search Results "Reach Range"
Filters
Commonly Searched Documents
-
Practice Putting Greens, Practice Teeing Grounds, and Teeing Stations at Driving Ranges: ADA Standard Section 238.3
-
Forward Approach and Reach
[See subsections ...]
-
407.12.3.2.1 Height (Section-by-Section Analysis)
depending on reach depth....
-
11B-238.3 Practice putting greens, practice teeing grounds, and teeing stations at driving ranges
At least 5 percent, but no fewer than one, of practice putting greens, practice teeing grounds, and teeing stations at driving ranges shall be designed and constructed so that a golf car...
-
Utility Sinks
If utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent (but not less than 1) in each accessible room or space must...
-
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis)
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis) This section proposes that, where a side approach is provided, the vertical reference plane must have a minimum...
-
407.12.1.2 Vertical Plane for Forward Reach (Section-by-Section Analysis)
407.12.1.2 Vertical Plane for Forward Reach (Section-by-Section Analysis) This section proposes that, where a forward reach is provided, the vertical reference plane must be, at a minimum...
-
Driving Ranges
Driving Ranges Both stand-alone driving ranges and driving ranges adjacent to a golf course that provide teeing stations or practice teeing grounds must comply with the following:...
-
Knee and Toe Space
If the forward reach to operable parts extends over an obstruction, such as a counter, clearances for toes and knees is required below....
-
§ 38.127(c)
(c) Controls and operating mechanisms (e.g., heating and air conditioning controls, lighting controls, call buttons, electrical outlets, etc.) shall be mounted no more than 48...
-
407.12.3.2.1 Height
Table 407.12.3.2.1 Operable Part Height Table 407.12.3.2.1 Operable Part Height Reach Depth Operable Part Height Less than 20 inches (510 mm) 48...
-
4.31.3* MOUNTING HEIGHT
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6....
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in Section 11B-609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate...
-
Paragraph (f) Operable with limited reach and strength (Section-by-Section Analysis)
Paragraph (f) Operable with limited reach and strength (Section-by-Section Analysis) Comment....
-
Construction and Manufacturing Tolerances: ADA Standard Section 104.1.1
Section 104.1.1 of the ADA Standards covers the most current information on dimensions in regards to construction and manufacturing tolerances in the ADA Standards.
-
1.1.2
1.1.2 When a dimension range is the regulatory requirement use the midpoint of the range as the drawing dimension....
-
302.8 With Limited Reach and Strength
Where a manual mode of operation is provided, ICT shall provide at least one mode of operation that is operable with limited reach and limited strength....
-
302.8 With Limited Reach and Strength
Where a manual mode of operation is provided, ICT shall provide at least one mode of operation that is operable with limited reach and limited strength....
-
407.8.2.1 Unobstructed Side Reach
Where the operable part is located 10 inches (255 mm) or less beyond the vertical reference plane, the operable part shall be 48 inches (1220 mm) high maximum and 15 inches (380 mm)...
-
407.12.2.1 Unobstructed Side Reach
Where the operable part is located 10 inches (255 mm) or less beyond the vertical reference plane, the operable part shall be 48 inches (1220 mm) high maximum and 15 inches (380 mm)...