The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
904.3.2 Counter
-
H22
Is a second horizontal grab bar at least 36 inches long securely mounted on the back wall with one end no more than 6 inches from the side wall 33 to 36 inches above the floor?...
-
3. Toilet Centerline
Is the accessible toilet in each accessible guestroom bathroom centered 18" from the adjacent side wall, which is the distance that will permit a person with a mobility impairment to use...
-
12. Reach Range
Are there towel racks or bars placed within 54" of the floor for side approach or 48" of the floor for forward approach so persons who use wheelchairs can approach and use the towel racks...
-
GUARD OR GUARDRAIL
A building component or a system of building components located at or near the open sides of elevated walking surfaces that minimizes the possibility of a fall from the walking surface to...
-
§ 37.131(a)(1)(i)
(i) The entity shall provide complementary paratransit service to origins and destinations within corridors with a width of three-fourths of a mile on each side of each fixed route....
-
11B-904.3.2 Counter
The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
-
11B-904.3.2 Counter
The top of the counter edge protection shall be 2 inches (51 mm) maximum above the top of the counter surface on the aisle side of the check-out counter....
-
F. Chapter 5: Doorways, Circulation Paths, and Fare Collection Devices
Additionally, in the final rule, the technical requirements for vertical clearances at doorways with lifts or ramps and for illumination at doorway areas have been restated using text in...
-
Pilot Rock BS Series Bike Stand
BS Series Bike Stands provide stalls on 16” centers (on same side) to fit most bicycles. Model BS-3SS: 2 ft.-10 in. long, parks 3 bikes, using one side....
-
Opening Force
Considering that closing force is 60% efficient, a 15 pound maximum for opening force may be sufficient for closure and positive latching of most doors, but is triple the recognized maximum...
-
Appendix 2: Survey Forms: Curb Ramps
Y N Y N Y N Y N Y N Y N Y N 9 Does CR have flared sides? If yes, answer one of the next two questions....
-
604 Water Closets and Toilet Compartments
Revisions to the requirements for water closets concern: location (604.2) clearance (604.3) grab bars (604.5) flush controls (604.6) dispensers (...
-
Exposed Pipes and Surfaces [4.19.4]
If an under-lavatory enclosure is used, the specified knee and toe clearances must be maintained....
-
Raised and Braille Characters on Hoistway Entrances [4.10.5]
Recommendation:Since Braille characters can be difficult to read if placed too close to raised characters, consider a vertical clearance of at least 3/8 inch....
-
Doors and Gates Operated Only By Security Personnel [§404.1, Ex]
, such as guards in a jail or prison, are exempt from requirements for hardware, closing speed, and opening force, but must meet all other requirements, including those for maneuvering clearance...
-
11B-226.1 General
Consider work surfaces that are flexible and permit installation at variable heights and clearances. ◼...
-
Camp Shelter
Camp Shelter—A small structure typically enclosed on three sides with a roof or overhang to provide campers and hikers cover from weather....
-
Camp Shelter
A small structure typically enclosed on three or all four sides, with a roof or overhang. Camp shelters are often located on trails. ...
-
1132A.2 Interior doors and secondary exterior doors
The provisions of this section shall apply to the dwelling unit side of doors leading from the interior of the dwelling unit to an unfinished basement or an attached garage....
-
11B-607.5 Controls
Controls shall be between the bathtub rim and grab bar, and between the open side of the bathtub and the centerline of the width of the bathtub....
-
1132A.2 Interior doors and secondary exterior doors
The provisions of this section shall apply to the dwelling unit side of doors leading from the interior of the dwelling unit to an unfinished basement or an attached garage....
-
11B-221.1 General
At least five percent of aisle seats (but not less than one) are required to either have no armrest on the aisle side or to have a removable or folding armrest on the aisle side....
-
Hager Companies Door Protection Plate 224S
Door Protection Plate 224S 0.062" gauge with 4-sided bevel Materials: - Aluminum, brass, bronze, stainless steel Options: - Self-adhesive tape available on all plates - Spanner...
