Table 1.2 lists the 24 organizations selected; each organization could designate a primary representative and a secondary representative who would participate in the absence of (or at the...
Search Results "Franchise Design"
Filters
Commonly Searched Documents
-
1.2 MDE Advisory Committee Membership
-
R304.5.3 Cross Slope
Pedestrian street crossings without yield or stop control are crossings where there is no yield or stop sign, or where there is a traffic signal that is designed for the green phase....
-
R101.1 General
Compliance with this document is mandatory when required by regulations issued by federal agencies that include accessibility standards for the design, construction, and alteration of pedestrian...
-
"1991 Standards" and "2004 ADAAG" (Section-by-Section Analysis)
The term "1991 Standards" refers to the currently enforceable ADA Standards for Accessible Design, codified at 28 CFR part 36, App. A. ...
-
J. Valet Parking and New Parking Garage
construct accessible parking spaces, entrances, and routes of travel as required by 2010 Standards §§ 208.1, 208.2, 208.2.4, 208.3.1, and 502.1-503.5, and to erect appropriate signage designating...
-
"1991 Standards" and "2004 ADAAG" (Section-by-Section Analysis)
The term "1991 Standards" refers to the currently enforceable ADA Standards for Accessible Design, codified at 28 CFR part 36, App. A. ...
-
ADA Requirements - Wheelchairs, Mobility Aids, and Other Power-Driven Mobility Devices
These requirements, or rules, clarify and refine issues that have arisen over the past 20 years and contain new, and updated, requirements, including the 2010 Standards for Accessible Design...
-
Sec.36.401(d)(1)(ii)(B)
The facility housing a "shopping center or shopping mall'' only includes floor levels housing at least one sales or rental establishment, or any floor level designed or intended for use...
-
Research Projects
The Board’s research program is focused on the study of accessibility relating to architecture and design, communication, and transportation....
-
Shared Use Paths
A shared use path is a multi-use path that is designed primarily for use by pedestrians and bicyclists for transportation and recreational purposes....
-
Outdoor Conditions [4.8.8]
Exterior ramps must be designed so that water does not accumulate on the ramp or landing surface. A slope up to 2% is allowed at landings for adequate drainage....
-
Measuring Opening Force
While there are instruments specifically designed for this purpose (e.g., tensionometer), a device as simple as a spring-loaded plunger or "fish" scale is effective in measuring the force...
-
Equivalent Facilitation [2.2]
This provides flexibility for new technologies and innovative designs solutions that may not have been taken into account when ADAAG was developed....
-
Definitions
“Accessible on Election Day” means that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is...
-
Rotational Penetrometer
The Rotational Penetrometer, developed by Beneficial Designs, uses a wheelchair caster placed on a spring loaded caliber in a metal tripod frame which suspends the caster about 6 inches...
-
On-Site Readers
If this happens, designate people to serve as on-site readers....
-
Three Additional Features for Van-Accessible Parking Spaces
(plan drawing showing a van-accessible parking space with a 96 inch wide designated parking space, a 96 inch wide min. marked access aisle and the following notes) Sign with...
-
Accessible Parking Spaces
When a business restripes a parking lot, it must provide accessible parking spaces as required by the ADA Standards for Accessible Design....
-
Research Projects
The Board’s research program is focused on the study of accessibility relating to architecture and design, communication, and transportation....
-
1607A.8.2 Grab bars, shower seats and dressing room bench seats
Grab bars, shower seats and dressing room bench seat systems shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab...
-
11B-803.1 General
Partitions and doors should be designed to ensure people using accessible dressing and fitting rooms privacy equivalent to that afforded other users of the facility....
-
1010.1.9.1 Hardware
These design requirements for door handles, pulls, latches, locks and other operating devices, intended for use on required means of egress doors in other than Group R and M occupancies...
-
11B-803.1 General
Partitions and doors should be designed to ensure people using accessible dressing and fitting rooms privacy equivalent to that afforded other users of the facility....