Gripping surfaces shall have a cross section complying with T303.3....
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
T303.3 Cross Section
-
M302.3 Supports
Transfer supports, armrests, and reclining surfaces shall comply with M302.3....
-
M301.3 Supports
Transfer supports, stirrups, and reclining surfaces shall comply with M301.3....
-
AJW Architectural Products US712 Series U7128B-1216 12"Wx16"H Security Concealed Mount Mirror, Angle Frame, Stainless Steel Surface
Product Features fabricated of #14 gauge stainless steel with a #4 satin finish Hooks Collapse To Prevent Injury Product Has Security Applications Product Specs Frame:...
-
M305.2.2 Length (Section-by-Section Analysis)
extend horizontally along the transfer surface to within three inches, to allow for manufacturing tolerances....
-
4. Comparison of Proposed Technical Provisions Applicable to Shared Use Paths and AASHTO Guide
R302.7 Surfaces....
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3....
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
M301.3 Supports
Transfer supports, leg supports, and reclining surfaces shall comply with M301.3....
-
Berm
Berm - A sloped surface at ground level designed to ascend or descend in elevation....
-
106.5.53 Ramp
A walking surface that has a running slope steeper than 1:20....
-
Executive summary
Results showed a consensus among studies that transferring to a higher surface implies greater exertion of the upper limb. ...
-
M302.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 39 inches (990 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
703.4.1 Height Above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
Ramps [4.8]
The curvature and slope typically result in an uneven surface that makes wheelchair maneuvering difficult because not all wheels rest on the surface....
-
Openings in Beach Access Routes
Openings are gaps in the surface of a beach access route. Gaps include spaces between the planks on a boardwalk and drainage holes in temporary or permanent surfaces....
-
Questionnaire
A full version of the questionnaire given to the subjects after traveling over each surface can be found in Appendix C. The questionnaire was developed by the study investigators....
-
M302.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
M301.4.1 Clearance in Base
provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface...
-
¾ Inch Minus and ¼ Inch Minus Limestone
The surface stayed soft under foot, enough to see footprints compacted and not return to the surface, but did not show any signs of erosion....
-
Soiltac Liquid Topical
The first noticeable signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
