Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
11B-803.6 Mirrors
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
Tent Pads and Tent Platforms
Accessible surfaces for pitching tents may or may not be at ground level....
-
Addendum A: List of Terms
Non-level Transfer- A transfer where the transfer surface is higher or lower than the wheelchair seat to floor height....
-
Accessible Slopes
Put the level on the surface in the direction you are measuring. ...
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
Study Population
As of May, 2014, 76 subjects participated in our study; however, not all of the subjects traveled over every surface....
-
R305.2.4 Pedestrian Refuge Islands
At cut-through pedestrian refuge islands, detectable warning surfaces shall be placed at the edges of the pedestrian island and shall be separated by a 610 mm (2.0 ft) minimum length of...
-
4(6)
(6) At the primary entry door to dwelling units with direct exterior access, outside landing surfaces constructed of impervious materials such as concrete, brick or flagstone, are no more...
-
11B-705.1.1.3 Color and Contrast
Detectable warning surfaces at transit boarding platform edges, bus stops, hazardous vehicular areas, reflecting pools, and track crossings shall comply with Section 11B-705.1.1.3.1....
-
Soiltac Powder Topical
As with the other three Soiltac surface applications, the first signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
Passing Spaces [1017.4]
Nominally planar means on the same nominal table surface (same nominal geometric surface plane) and the slopes of the table surface correspond to the running slope and cross slope of the...
-
Preliminary Guidelines for Vitri-Turf SEWF Installation
Do not saturate the surface with these lubricants. After compaction, thickness will be approximately 40 mm (1.6 in.)....
-
705 Detectable Warnings
Section 705 provides the technical specifications for detectable warnings, a distinctively textured surface of truncated domes identifiable by cane and underfoot....
-
Costs and Personnel Time for Beach Path Installation
Equipment and tool rental (market value) $100 Personnel time Base prep and geotextile installation, 4 h @ $10/h $40 Bonded surface...
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
11B-903.4 Back support
Back support shall be 48 inches (1219 mm) long minimum and shall extend from a point 2 inches (51 mm) maximum above the seat surface to a point 18 inches (457 mm) minimum above the seat...
-
11B-705.3 Product Approval
Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
-
Foot-candle
The illumination on a surface one square foot in area on which there is a uniformly distributed flux of one lumen, or the illuminance produced on a surface all points of which are at a distance...