In its proposed rule, the Access Board proposed that the “height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured...
Search Results "Dining Surface"
Filters
Commonly Searched Documents
-
ALIGNMENT OF 19-INCH RECOMMENDATION WITH ACCESS BOARD PROPOSED RULEMAKING
-
5.4.1.2 Transfer and Positioning Support Location for Imaging Equipment
Transfer supports should be provided for imaging equipment with transfer surfaces with depths of less than or equal to 24 inches....
-
Edge Protection
Edge Protection Where railings, guards, or handrails are provided, edge protection must be provided and extend a minimum of 2 inches above the ground or deck surface....
-
22. How can I get copies of the ASTM standards that apply to play areas?
American Society for Testing and Materials, 100 Bar Harbor Drive, West Conshohocken, Pennsylvania 19428, www.astm.org: ASTM F 1292-99 Standard Specification for Impact Attenuation of Surface...
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
I. Public Toilet Rooms
In all public and common use toilet rooms throughout the Hotel and the Tower, Defendants will provide at least one lavatory with a counter-top that is 34 inches above the finish floor surface...
-
Card Catalogs and Magazine Displays [8.4]
Requirements for fixed counters and tables [4.32] specify a surface height (34 inches maximum) and knee clearance below appropriate for extended use as a writing/work surface....
-
Slope
The incline of a surface....
-
Slope
The incline of a surface. ...
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
However, shorthand references to 19 inches as the minimum standard as used in this minority report should not be equated with a 19-inch transfer surface height, for two major reasons....
-
¼ Inch Minus Limestone
The surface was installed in two rolled and compacted 3 inch lifts....
-
Areas for further work
Areas for further work In the process of assisting the various organizations that represent surface materials and professional groups the following issues were identified as parameters...
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings. ...
-
1011.2.4 Openings
Openings in the clear ground space surface shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1011.2.4 Openings....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
11B-803.6 Mirrors
Mirrors shall be installed with the bottom edge of the reflecting surface 20 inches (508 mm) maximum above the finish floor or ground....
-
Eunice Noell-Waggoner, IES, LC. Value, Contrast and Reflections
Reflective & Transparent Surfaces can be Dangerous Vertical Surfaces (slide 4) Two examples are shown of hazards from reflective and transparent vertical surfaces....
-
Literature Cited
ASTM F1292 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment, ASTM, West Conshohocken,PA 19428 American Society for Testing and Materials...
-
Identification: ADA Standard Section 502.6
Section 502.6 covers the current ADA Standards for parking space identification signs.
-
Finish and Contrast: ADA Standard Section 703.7.1
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
Finish and Contrast: ADA Standard Section 703.5.1
Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text...
-
Handrail Extensions: ADA Standard Section 505.10
Section 505.10 covers the current ADA Standards for handrail extensions.