turn) between two corridor walls, two 90 degree turns around an obstacle that was 1200 mm wide, two 90 degree turns around an obstacle that was narrower than1200 mm, 90 degree turn on a ramp...
Search Results "Curb Ramp Top Landing"
-
UDI
-
1127B.1
be designed to provide access to all entrances and exterior ground floor exits, and access to normal paths of travel, and where necessary to provide access, shall incorporate pedestrian ramps...
-
Reasonable Modification of Policies and Procedures
If a city requires a 12-foot set-back from the curb in the central business district, it may be reasonable to grant a 3-foot variance for a store wishing to install a ramp at its entrance...
-
A. Accessible Voting Program
condition on Election Day those features of facilities and equipment (including, but not limited to, permanent equipment such as lifts and elevators, and temporary equipment such as portable ramps...
-
Door and Signal Timing
Destination-oriented elevators may have call buttons located outside elevator landing areas and have enhanced programming features for the response time of cars....
-
11B-410.6 Doors and gates
Exception: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
11B-410.6 Doors and gates
Exception: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
Examination Tables
Treatment tables typically have a flat top. Some models have adjustable backrests, but the backrests typically cannot support patients in a sitting position....
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
M302.2.5 Unobstructed Transfer
Obstructions no more than 3 inches (75 mm) deep shall be permitted to extend beyond transfer sides of transfer surfaces provided that such obstructions do not protrude above the tops of...
-
R305.1.1 Dome Size
The truncated domes shall have a base diameter of 23 mm (0.9 in) minimum and 36 mm (1.4 in) maximum, a top diameter of 50 percent of the base diameter minimum and 65 percent of the base...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
804.2.1 Pass Through Kitchen
counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing base cabinets, counter tops...
-
Original research for ANSI A117.1 (1957 - 1961)
In the original research for ANSI A117.1 - 1961, American National Standard Specifications for Making Buildings and Facilities Accessible to, and Usable by, the Physically Handicapped, ramps...
-
502.2 Vehicle Spaces
See section 406.5 curb ramp location....
-
Utility Sinks
If utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent (but not less than 1) in each accessible room or space must...
-
Flush Controls On Toilets
With requirement's for saving of water within certain jurisdictions there are a number of toilets out there with the flush control as a button on the top of the tank. ...
-
Increasing Opportunities for Access on the Appalachian Trail: A Design Guide
This law, and the extensive land protection programs that followed, underscore the significance of the Trail as one of our nation’s most important recreational and scenic resources....
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
The work to negotiate a ramp was linearly related to the angle of the ramp....
-
Slope Game: Dive Into the Pulse of Neon Speed
But as the speed ramps up, those two directions feel like the difference between mastery and chaos....
-
Examples of alternative ways to serve a customer when barrier removal is not feasible are:
Examples of alternative ways to serve a customer when barrier removal is not feasible are: At a dry cleaner's, providing curb-side service for a customer dropping off or picking up...
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
-
Track Crossing
The proposed rule required route surfaces to be level with the rail top, but permitted a 2 ½ inch gap at the inner edge of rails to accommodate wheel flanges (1003.2.7)....
-
M302.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A....
