Available with phenolic tops (shown) or padded naugahyde which are seam-sealed to prevent any water or bacteria penetration. Left or right sided tops....
Search Results "Curb Ramp Top Landing"
Filters
Commonly Searched Documents
-
Access-Able Designs Wall Mounted Shower Transfer Bench SH-400
-
Current Accessibility Guidelines That Apply to the Forest Service
The Forest Service and those working with or for the Forest Service on National Forest System land must comply with the following enforceable guidelines and standards when designing, constructing...
-
407.12 Reach Height (Section-by-Section Analysis)
concerns that the word “freestanding” implies an independent supporting structure that may not always be in place, such as with a multifunction printer specifically designed for table-top...
-
Selection of Variables
C Hand strength [operating equipment]; arm strength [transfers] D Field of vision [up, sideways, down] E Measurements of chair and user (floor to top...
-
1003.2.13.2 Enclosed exit stairways
of an accessible means of egress, shall have a clear width of 48 inches (1219 mm) minimum between handrails and shall either incorporate an area of refuge within an enlarged floor-level landing...
-
Rough Grade Site Inspection
specified accessible routes from all entrances and exits to common and public use areas on the site. 11B-206.2.2 If site conditions have swamp type lands...
-
Rough Grade Site Inspection
specified accessible routes from all entrances and exits to common and public use areas on the site. 11B-206.2.2 If site conditions have swamp type lands...
-
703.2.7 Character Spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
M301.2.1 Adjustability (Section-by-Section Analysis)
transfer heights located between the low and high transfer heights, separated by one inch minimum increments; and (4) the transfer surface height will be measured from the floor to the top...
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
provision which permits obstructions of no more than three inches to extend beyond the transfer side of the transfer surface, provided that such obstructions do not protrude above the top...
-
703.2.7 Character Spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
703.2.7 Character Spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
703.2.7 Character Spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
604.7 Dispensers
If toilet paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of...
-
610.3 Shower Compartment Seats
The top of the seat shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor. Seats shall comply with 610.3.1 or 610.3.2....
-
Running Slope [1018.7.1]
running slope of a segment of beach access route is steeper than 1:20 (5 percent), the maximum length of the segment is specified in table 6, and a resting interval must be provided at the top...
-
Facility
The tops of dining surfaces and work surfaces shall be 28 inches minimum and 34 inches maximum above the finish floor or ground....
-
L. Lavatory
Is there at least one lavatory (wash basin) in each public restroom that has each of the following characteristics... ...a 29" high clearance under the front edge and the top of the bowl...
-
604.7 Dispensers
If toilet paper dispensers are installed above the side wall grab bar, the outlet of the toilet paper dispenser must be 48 inches (1220 mm) maximum above the finish floor and the top of...
-
Door and Gate Surfaces [§404.2.10]
of the finish floor or ground Existing doors or gates with kick plates (so long as cavities created by kick plates are capped) Tempered glass doors without stiles if the top...
-
11B-703.2.7 Character spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
11B-703.2.7 Character spacing
minimum and 4 times the raised character stroke width maximum at the base of the cross sections, and 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum at the top...
-
R309.5.1 Location
Locating parking meters at the head or foot of the parking space permits deployment of a van side-lift or ramp or the vehicle occupant to transfer to a wheelchair or scooter....
-
Special Technical Provisions for Alterations to Existing Buildings and Facilities [4.1.6(3)]
Section 4.1.6(3) recognizes certain allowances where technical feasibility is encountered, such as steeper slopes for short ramps....