[2010 ADA Standards] 405.9.1 Extended Floor or Ground Surface....
Search Results "Floor Slope"
-
11B-405.9.1 Reserved.
-
11B-405.9.1 Reserved.
[2010 ADA Standards] 405.9.1 Extended Floor or Ground Surface....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
Section 307 Protruding Objects
This dryer protrudes more than 4" from the wall and is greater than 27" above the finish floor. Isn't this a violation of Section 307 Protruding Objects?...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Passing Spaces [1017.4]
Nominally planar means on the same nominal table surface (same nominal geometric surface plane) and the slopes of the table surface correspond to the running slope and cross slope of the...
-
General: ADA Standard Section 306.2.1
Section 306.2.1 of the ADA Standards covers information in the current ADA Standards for toe clearance.
-
Location
The slope along the accessible route should not be greater than 1:12 in the direction of travel....
-
Technical Infeasibility
plumbing, life safety or other codes (such as when combining two toilet stalls to create an accessible stall would violate the plumbing code’s required fixture count); meeting slope...
-
Location
The slope along the accessible route should not be greater than 1:12 in the direction of travel....
-
1.0 APPLICATION
Where existing individual site furnishings are altered or replaced, the floor or ground surface under or around them is not required to be altered solely because an accessible furnishing...
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
11B-306.2.1 General
Space under an element between the finish floor or ground and 9 inches (229 mm) above the finish floor or ground shall be considered toe clearance and shall comply with Section 11B-306.2...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
Maneuvering Space Where Ramps are Provided
The space must have a slope no steeper than 1:48 in all directions. ...
-
Transition Plates
Transition Plates Transition plates are sloping pedestrian walking surfaces located at the end of a gangway....
-
11B-206.2.3 Multi-story buildings and facilities
For example, a 3-story office building with 4500 sf on the first floor, 2500 sf on the second floor and 1500 sf on the third floor would not qualify for the exception because one of the...
-
505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....
-
704.11.1 Parapet construction
Where the roof slopes toward a parapet at a slope greater than two units vertical in 12 units horizontal (16.7-percent slope), the parapet shall extend to the same height as any portion...
-
11B-505.1 General
Handrails are not required on walking surfaces with running slopes less than 1:20....