The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station...
Search Results "Expected Maximum Flight Duration"
Filters
Commonly Searched Documents
-
§ 38.125(b)(8) Platform entrance ramp
-
§ 38.83(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and the transition from the station platform...
-
§ 38.95(b)(8) Platform entrance ramp
The entrance ramp, or loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station...
-
II-3.4000 Separate benefit/integrated setting
The major principles of mainstreaming are -- 1) Individuals with disabilities must be integrated to the maximum extent appropriate. 2) Separate programs are permitted where necessary...
-
11B-502.6.4.1
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-307.4 Vertical clearance
The leading edge of such guardrail or barrier shall be located 27 inches (686 mm) maximum above the finish floor or ground....
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
Social Security Disability Benefits Guide
We’ll walk you through each step of the process, and tell you what to expect during each stage of your Social Security disability application....
-
Rebuilding Together Mohawk Valley - Clinton, NY
Our Mission The number of low-income homeowners increases each year and is expected to grow to an astonishing 28.5 million by 2010....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Since there is no change to the wording of Section 11B-805.6, there is no reason to expect that OSHPD will change its interpretation....
-
M305.2.1 Location (Section-by-Section Analysis)
This commenter noted that an adjacent transfer support would be more effective, but would conflict with the provider expectations of bed and stretcher side rails....
-
4.3.8 Operating forces
For other types of operable parts, the upper limit for operating force should be retained at a maximum of 5 lbf (22 N) to accommodate 95% of the sample....
-
Accessibility - Flatness and Lippage
Mortar setting beds for concrete pavers and paving slabs Joint width between paving units with chamfers (See Figure I) Maximum 3/8 in. (10 rom) - The surface of the mortared joint...
-
2.2.3 Functional Reach
Use of the electromechanical probe required manually digitizing the 3-D location of the maximum reach point after the cylinder was positioned (Figure 2‒3)....
-
405.2 Slope (Exception 2), 405.6 Rise (Exception)
The running slope of ramp runs must not be steeper than 1:12 and any ramp rise must be 30 inches maximum....
-
704.8 Allowable area of openings
The maximum area of unprotected or protected openings permitted in an exterior wall in any story shall not exceed the values set forth in Table 704.8....
-
Toilet Paper Dispensers
The provisions for toilet paper dispensers at section 604.7 of the 2010 Standards require the dispenser to be located seven inches minimum and nine inches maximum in front of the water closet...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
Features of Accessible Parking Spaces
Access aisle width is at least 60 inches, must be at the same level and the same length as the adjacent parking space(s) it serves, maximum slope in all directions is 1:48, and access aisle...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
11B-407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
1009.2.1 Pool Lift Location
Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum....
-
§382.9(e)(3)
The Department will, to the maximum extent feasible, respond to such requests within 180 days of receiving them....
