However, when turning at higher speeds, these vehicles can be unstable....
Search Results "Clear Width at Turn"
Filters
Commonly Searched Documents
-
Recumbent Tricycles
-
11B-802.1.5 Overlap
The term "circulation paths" used in Section 11B-802.1.5 means aisle width required by applicable building or life safety codes for the specific assembly occupancy....
-
Lift-U® Fold-Out Rising Floor Ramp
Gaps in floor when deployed – minimal Hinge Knuckles between Ramp & Bus structure – eliminated SPECIFICATIONS Clear width at ramp surface – 30 Inches Minimum...
-
T402 Ramps and Bridgeplates
technical requirements for ramps and bridgeplates in the 2016 Non-Rail Vehicle Guidelines include provisions on design load, installation and operation, emergency operation, surfaces, clear...
-
10. I have already been sued, so I am clear.
False! If you have been sued or paid a settlement and did not fix the issue, then you are still at risk. If you did fix the issue, you may still be responsible for accessibility or...
-
Oval Window Audio Satellite III — Large Area Induction Hearing Loop System
Depending on planned loop dimensions, the Satellite III hearing assistance system comes complete with: A 250-foot spool of two conductor 14-gauge clear wire for connecting as a two...
-
4.30.2* Character Proportion
Letters and numbers on signs shall have a width-to-height ratio between 3:5 and 1:1 and a stroke-width to- height ratio between 1:5 and 1:10....
-
4.30.2* CHARACTER PROPORTION
Letters and numbers on signs shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10....
-
GE Cafe™ Series 30" Free-Standing Gas Double Oven with Convection Range CGS990SETSS
140F degree simmer Tri-Ring Burner (1) 20,000 BTU / 140F degree simmer All-Purpose Burners (1) 9,100 BTU/150F degree simmer Valves (Degree of Turn...
-
Q3.) What are the types of “manufacturing processes” that were anticipated where the advisory says “tolerances recognized by this provision include… “those that may be a necessary consequence of a particular manufacturing process”?
Therefore, the width at the back will be smaller than the width at the front. ...
-
11B-505.2 Where required
Exceptions: In assembly areas, handrails shall not be required on both sides of aisle ramps where a handrail is provided at either side or within the aisle width....
-
406 Curb Ramps
These include specifications for running slope, surface, clear width, and wet conditions. Consistent with the scope of the guidelines, these requirements apply to facilities on sites....
-
Scoping [4.1.2(1), 4.1.3(1)] and Location [4.3.2]
Clear width, surface texture, running and cross slope, and the treatment of changes in level help determine the usability of walking surfaces by people with mobility impairments....
-
LaCantina Aluminum Thermally Controlled Slider System
Kitchen servery pass through Sizing and Configuration The Aluminum Thermally Controlled system is available in any configuration with panels up to 8' wide and 12' tall, panel width...
-
M302.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M301.4.1 Clearance in Base
Where the width of examination surfaces is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M302.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M301.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
809 Residential Dwelling Units
809 Residential Dwelling Units 809 Residential Dwelling Units 809.1 General 809.1 General 809.2 Accessible Routes 809.2.1 Location 809.2.2 Turning...
-
412.8.2 Voice and Hearing Carry Over
ICT shall provide a microphone capable of being turned on and off to allow the user to intermix speech with TTY use....
-
Rockwood Manufacturing Company 70REA Push Plate - .050" Thick 3" x 12" Plate
., 70REA US32D or for non-standard size 70 (width x height) and finish. Specify any additional optional features. Options: • Custom sizes available upon request....
-
Rockwood Manufacturing Company 71A Push Plate - .062" Thick 3" X 12" Plate
., 71A US32D or for non-standard size 71 (width x height) and finish. Specify any additional optional features. Options: • Custom sizes available upon request....
-
Rockwood Manufacturing Company 70A Push Plate - .050" Thick 3" x 12" Plate
Ordering: Specify plate number followed by size designation and finish (70A US32D) or for non-standard size 70 (width x height) and finish. Specify any additional optional features....
-
4.1 Wheeled Mobility Device Dimensions
Data on occupied device sizes is most valuable for establishing clear floor area requirements....
