Turned aluminum structure and heat sink coated in single or double color with polyester powders. Magnetic finish frame to hide the fixing screws. ...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
Anna LED Wall Mount Luminaire by DesignPlan
-
M302 Diagnostic Equipment Used by patients in Seated Position
It is important to create a distinction in the definition of these products so as to ensure that clinical products such as Examination Chairs and Stretcher Chairs fall under the extent of...
-
T201 General
Buses, OTRBs, and vans acquired or remanufactured by entities covered by the ADA must comply with the scoping requirements in Chapter 2 to the extent required by DOT’s implementing regulations...
-
810.2.2 Dimensions
of 36 CFR Part 1191 has modified 810.2.2 as follows: Access Board’s Note to Reader: The Department of Transportation’s ADA standards indicate that compliance is required to the extent...
-
F206.2.3.1 Stairs and Escalators in Existing Buildings
In alterations and additions, where an escalator or stair is provided where none existed previously and major structural modifications are necessary for the installation, an accessible route...
-
206.2.3.1 Stairs and Escalators in Existing Buildings
In alterations and additions, where an escalator or stair is provided where none existed previously and major structural modifications are necessary for the installation, an accessible route...
-
2.5 Physical Accessibility.
All airports under Section 504 were required to submit a transition plan to the FAA for approval "where extensive structural changes" were necessary....
-
ADA Guide for Small Towns
Disclaimer The ADA authorizes the Department of Justice to provide technical assistance to individuals and entities that have rights or responsibilities under the Act....
-
F244.2.3 Elements within Camping Units with Mobility Features
Where these elements are provided within a camping unit, at least one of each type of element is required to comply with the applicable technical requirements for the element....
-
1017.9 Protruding Objects
This section requires constructed elements on trails, resting intervals, and passing spaces to comply with the technical requirements for protruding objects in 307 of the Architectural Barriers...
-
202.3.1 Prohibited Reduction in Access
Those regulations state: “If the 2010 Standards reduce the technical requirements or the number of required accessible elements below the number required by the 1991 Standards, the technical...
-
Entry Points and Seats: ADA Standard Section 1008.4.4
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.3.3
Section 608.3.3 covers the current ADA Standards for grab bars in alternate roll-in type shower compartments.
-
11B-608.3.3 Alternate roll-in type shower compartments
Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls....
-
11B-608.3.3 Alternate roll-in type shower compartments
Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls....
-
Dome Spacing: ADA Standard Section 705.1.2
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
§ 35.137(d) Inquiry into use of power-driven mobility device
A public entity shall not ask a person using a mobility device questions about the nature and extent of the person's disability....
-
General [§202.1]
The extent of application is largely determined by a project’s scope of work as the standards apply to those elements or spaces that are altered or added....
-
R405 Knee and Toe Clearance (Section-by-Section Analysis)
R405 Knee and Toe Clearance (Section-by-Section Analysis) The technical requirements for knee and toe clearance apply where space beneath an element is included as part of the clear space...
-
Scoping Requirements for Elements and Spaces [§204 – §243]
Scoping Requirements for Elements and Spaces [§204 – §243] Scoping provisions for elements and spaces, which are summarized here, are further discussed with relevant technical provisions...
-
11B-248.2 Employee work areas
ETA Editor's Note The scoping and technical requirements for common use areas and employee work areas are new in CBC 2019....
-
§35.150 Existing facilities (Section-by-Section Analysis)
Structural changes in existing facilities are required only when there is no other feasible way to make the public entity's program accessible....
-
11B-705.1.1.1 Dome size
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (22.9 mm) minimum and 0.92 inch (23.4 mm) maximum, a top diameter of 0.45 inch (11.4 mm) minimum and...
-
610.3.2 L-Shaped Seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....