the "Trail Construction and Maintenance Notebook" in 1996, several excellent books about trail construction and maintenance have been published by the International Mountain Bicycling Association...
Search Results "BHMA: Builders Hardware Manufacturers Association"
Filters
Commonly Searched Documents
-
Trail Construction and Maintenance Notebook - 2007 Edition
-
8. Batteries
The appropriate number of batteries should be calculated using the manufacturer’s estimate of the hours of battery life while the device is in use and the information provided in the physician...
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
facilitate medical examinations by the medical clinician.17 Finally, it is important to note the requirements for tolerancing under current regulations: 104.1.1 Construction and Manufacturing...
-
New Accessible Handpump for Campgrounds
Ordering an Accessible Handpump—The Simple Pump Co. is now manufacturing an accessible handpump, the ADA 100 Handpump....
-
Exceptions Considered for Wheelchair Spaces on Raised Platforms
wheelchair spaces on diagnostic equipment with raised platforms, comments are requested on the following questions: a) What would be the incremental costs for the design or redesign and manufacture...
-
Panda S.15 All Wood with Aluminum Core Lift & Slide System
By integrating an aluminum core to the profile and incorporating heavy duty hardware, this system is able to achieve greater tolerances....
-
Section 1193.43 Output, display, and control functions [1193.37 in the NPRM] (Section-by-Section Analysis)
this section, the Board sought comment (Question 10) on whether moving the requirements of paragraphs (b)(9) and (b)(10) to a different section would be less confusing to designers and manufacturers...
-
VII. Effective Date
Manufacturers of Section 255-covered telecommunications equipment and customer premises equipment need not comply with the Board’s revised 255 Guidelines until incorporated into revised...
-
B. Proposed 255 Guidelines
Requirement for RTT functionality: Just as the proposed 508 Standards would require federal agencies to offer RTT functionality in certain ICT, the proposed 255 Guidelines would require the manufacturers...
-
Selection of Trail Surface Materials
materials (eight organic or natural by-product soil stabilizers, and three aggregate surfaces) were chosen based on their compatibility with existing soil and/or aggregate composition, and the manufacturer’s...
-
3.3.1 Unoccupied Device Width
The U.S. standards, generally accepted by the other countries, were derived from manufacturers’ data in the 1970’s and did not include many of WhMD technologies that are in use today....
-
2.1 Participants’ Vision
The chart was illuminated uniformly according to the instructions provided by the manufacturer. Figure 6 shows the distribution of participants’ contrast sensitivity scores....
-
Appendix E: Vision Tests
The book of test plates was viewed on a dedicated easel under simulated daylight illumination as recommended by the manufacturer....
-
§1607.5 General standards for validity studies.
standardized tests and other selection procedures, such as those described in the Standards for Educational and Psychological Tests prepared by a joint committee of the American Psychological Association...
-
Implementation Approach and Schedule
The second phase would require all pages associated with obtaining core air travel services and information related to these core services, either to be directly conformant on the carrier's...
-
Panda S.10 All Aluminum Lift & Slide System
Profiles: Manufactured from 6063-T5 extruded aluminum with a profile thickness of 2 3/4″ allowing for oversized panels....
-
Cal-Royal Products Swing Clear Hinges
TYPES OF FINISHES All steel and brass material hinges can be plated to match the available finishes that are listed in the American National Standards Institute or ANSI, standard ANSI/BHMA...
-
Architectural Barriers
include parking spaces that are too narrow to accommodate people who use wheelchairs; a step or steps at the entrance or to part of the selling space of a store; round doorknobs or door hardware...
-
III. Proposed alternative mechanisms to enhance patient access to diagnostic imaging equipment
DXA bone densitometry systems are currently at a fixed height of 25-28 inches because the imaging hardware is located beneath the patient and the precise position of the patient support...
-
ADA Requirements
The Standards require door hardware, heating and air conditioning controls, and faucet controls that do not require tight pinching, twisting, or grasping for persons with limited use of...
-
Alterations and Additions
Alterations can be as limited as the replacement of a fixture or element, such as a lavatory, toilet, or piece of door hardware....
-
68.20(d) Public Accommodations
or other place of exhibition or entertainment; (4) an auditorium, convention center, lecture hall, or other place of public gathering; (5) a bakery, grocery store, clothing store, hardware...
-
UltraPlay Engineered Wood Fiber Surface
Manufactured from engineered, non-toxic, crushed wood fiber Is a good solution for playgrounds erected on dirt or grass Once settled, forms a "knitted" or compacted layer that will support...
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
Installing accessible door hardware. 12. Installing grab bars in toilet stalls. 13. Rearranging toilet partitions to increase maneuvering space. 14. ...
