Press Release The parties to this Settlement Agreement are the United States of America and the City of DeKalb, Illinois....
Search Results "Unit of Measurement"
-
Press Release
-
1.6.17 Sterile Area.
A portion of an airport, specified in the airport security program, in which certain security measures specified in 49 CFR part 1542, Airport Security, are carried out....
-
2. Referenced Documents
2.1 ASTM standards E867 Standard Terminology Relating to Vehicle-Pavement Systems E1364 Standard Test Method for Measuring Road Roughness by Static Level Method E1926 Standard...
-
Acknowledgments
Acknowledgments The development of objective surface measurement devices and objective surface testing was conducted with funding from the National Center for Medical Rehabilitation Research...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
§8.27(b)
(b) When offering an accessible unit to an applicant not having handicaps requiring the accessibility features of the unit, the owner or manager may require the applicant to agree (and may...
-
1128A.1 General
Covered multifamily dwelling units shall be adaptable and accessible into and throughout the dwelling unit as provided in this division....
-
M301.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
1013.4 Height
Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
-
702.9.1 TIA-1083-B
Telecommunications—Communications Products—Handset Magnetic Measurement Procedures and Performance Requirements, October 2015, IBR approved for Appendix C, Section 412.3.2....
-
§ 35.151(b)(2)
(2) The path of travel requirements of § 35.151(b)(4) shall not apply to measures taken solely to comply with the program accessibility requirements of this section....
-
4.15.2* Spout Height
Spouts shall be no higher than 36 in (915 mm), measured from the floor or ground surfaces to the spout outlet (see Fig. 27(a))....
-
Side Approach
Side Approach The maximum reach depth for a high (54 inch maximum) reach is 10 inches, measured from the clear floor space....
-
1013.4 Height
Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
407.4.8.2.2 Signal Level
The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator....
-
1009.4.2 Height
The height of the transfer wall shall be 16 inches (405 mm) minimum and 19 inches (485 mm) maximum measured from the deck....
-
Two Drinking Fountains
Commenters also opposed specific recognition of "high-low" units as an alternative to two separate units since other types, such as single bowl units with two spouts, are commercially available...
-
I. Slip Resistant Surface—Aisles, Steps, Floor Areas Where People Walk, Floor Areas in Securement Locations, Lift Platforms, Ramps
While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
-
Study Limitations
distribution of participants by user type as shown in the following tables may not be representative of the overall user population on the three trails, nor of shared use paths throughout the United...
-
Interchangeability: ADA Standard Section 106.4
Section 106.4 of the ADA Standards covers information on the interchangeability of terms used throughout the ADA Standards.
-
Doorbell Factory Round Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted stainless steel push button and mounting screws Measures 2 3/4" round Usually ships in 1-3 business...
