Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
Search Results "Unit of Measurement"
-
1013.4 Height
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
Press Release
Press Release The parties to this Settlement Agreement are the United States of America and the City of DeKalb, Illinois....
-
Doorbell Factory Round Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted stainless steel push button and mounting screws Measures 2 3/4" round Usually ships in 1-3 business...
-
Interchangeability: ADA Standard Section 106.4
Section 106.4 of the ADA Standards covers information on the interchangeability of terms used throughout the ADA Standards.
-
§8.27(b)
(b) When offering an accessible unit to an applicant not having handicaps requiring the accessibility features of the unit, the owner or manager may require the applicant to agree (and may...
-
1128A.1 General
Covered multifamily dwelling units shall be adaptable and accessible into and throughout the dwelling unit as provided in this division....
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
Two Drinking Fountains
Commenters also opposed specific recognition of "high-low" units as an alternative to two separate units since other types, such as single bowl units with two spouts, are commercially available...
-
5.1.2 Transfer Surface High Height
The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.34.5.2(2)
(2) The height of the water closet shall be at least 15 in (380 mm), and no more than 19 in (485 mm), measured to the top of the toilet seat....
-
§ 37.155(a)(1)
(1) Effects on current fixed route service, including reallocation of accessible fixed route vehicles and potential reduction in service, measured by service miles;...
-
AJW Architectural Products U134EA 33 fl oz. Automatic Liquid Soap Dispenser - Surface Mounted
A pre-measured amount of soap will dispense. Unit is operated by three (3) "C" batteries, not provided, Alkaline batteries are recommended for best performance....
-
Whitehall Mfg. WH2125A On-Floor Bariatric Stainless Steel Toilet
The unit is fabricated of 14 gage, type 304 stainless steel and is seamless welded construction. The exterior and bowl interior has a satin finish....
-
Seating Locations
Remember, when measuring the accessible route through the space, measure the aisle width as if the chairs are pulled out and occupied....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
13 [§ 4.7.10]
When taking this measurement, the measuring tape should be aligned parallel to the ramp run itself and should stretch from the intersection of the ramp and gutter to the innermost edge of...
-
M304.2.1 Slip Resistant (Section-by-Section Analysis)
One manufacturer commented on this requirement, requesting that the rule provide clarification on how to define or measure a standing surface as “slip resistant.”...
