For example, 806 addresses guest rooms in transient lodging facilities while 902 contains the technical specifications for dining surfaces....
Search Results "Stable Surface"
-
Scope: ADA Standard Section 801.1
-
DETECTABLE WARNING
[DSA-AC] A standardized surface feature built in or applied to walking surfaces or other elements to warn persons with visual impairments of hazards on a circulation path....
-
DETECTABLE WARNING
[DSA-AC] A standardized surface feature built in or applied to walking surfaces or other elements to warn persons with visual impairments of hazards on a circulation path....
-
SafePath VulcanLanding™ Rubber Transition Ramp
Modifying vertical rises at door thresholds often requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface...
-
Exemptions for Entire Trail or Beach Access Route
combination of running slope and cross slope exceeds 40 percent for over 20 feet; A trail obstacle 30 inches high or more runs across the full tread width of the trail; The trail surface...
-
Transition Plate
A sloping pedestrian walking surface located at the end(s) of a gangway....
-
11B-705.1.2.5 Blended transitions
Editor's Note: From DSA's "Summary of New and Amended 2025 California Building Code (CBC) Regulations for Accessibility in the Triennial Code Cycle: "Requirements for detectable warning surfaces...
-
Permitted Protrusions in Wheelchair Spaces: ADA Standard Section 1002.4.4.3
protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface...
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum above the floor or ground surface...
-
Ramp
A walking surface that has a running slope steeper than 1:20....
-
HEWI Hinged Support Rail Mono WARM TOUCH
core - integrated wall mounting plate made of metal with cap made of chrome-look coated polyamide - wall mounting plate 181 mm high and 130 mm wide - rail ø 33 mm, 600 mm projection - stable...
-
Detectable Warnings: ADA Standard Section 705
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
GRADE BREAK
[DSA-AC] The line where two surface planes with different slopes meet....
-
General: ADA Standard Section 705.1
Detectable warnings shall consist of a surface of truncated domes and shall comply with 705....
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
TRANSITION PLATE
[DSA-AC] A sloping pedestrian walking surface located at the end(s) of a gangway....
-
Walk
An exterior prepared surface for pedestrian use, including pedestrian areas such as plazas and courts....
-
5.4.10 Transfer Support Fittings Recommendations for M301 and M302
Rationale for the recommendation Transfer supports that move when locked for use would create an unacceptable risk for patients relying on stable support....
-
Benches
Do not allow the slope of the clear floor or ground space to exceed 1:48 (2 percent) in any direction, except if the surface isn't paved or built with boards, the slope may be up to 1:33...
-
Height Above Finish Floor or Ground: ADA Standard Section 703.4.1
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
11B-801.1 Scope
For example, Section 11B-806 addresses guest rooms in transient lodging facilities while Section 11B-902 contains the technical specifications for dining surfaces....
-
11B-405.9.2 Curb or barrier
or barrier shall be provided that prevents the passage of a 4-inch (102 mm) diameter sphere, where any portion of the sphere is within 4 inches (102 mm) of the finish floor or ground surface...
