Where two automatic teller machines or fare machines are provided at a location, one shall comply with Sections 11B-707.2 through 11B-707.8 and one shall comply with Sections 11B-707.3,...
Search Results "Fishing Location"
-
11B-220.1.2 Two automatic teller machines or fare machines
- Salsbury Industries Cell Phone Storage Lockers
- Sargent Wall and Frame Switch Interface for Door Operators
- Verifone MX 860 Point of Sale Machine with Credit Card Reader
- ViewPlus Technologies Audio Graphing Calculator
- Elkay Wall Mount Bi-Level ADA Water Cooler EZSTL8LC
-
Re: Lavatories Adjacent to Partitions
The question is where is the location of dispenser/element in question. 11B-606.6 requires lavatories adjacent to sidewall or partition to be a minimum of 18" to the centerline of the...
-
2.6 Communications.
under the 2010 ADA Standards for Accessible Design, there are signage requirements that address the need for directional and informational signs that communicate information about the location...
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are less than 1000 square feet (93 m2) and defined by permanently installed partitions, counters, casework, or furnishings...
-
Electronic Submission and Posting of Public Comments
You must also locate all the personal identifying information you do not want posted online in the first paragraph of your comment and identify information you want redacted....
-
Electronic Submission and Posting of Public Comments
You must also locate all the personal identifying information you do not want posted online in the first paragraph of your comment and identify information you want redacted....
-
Apps
There are many emergency apps to choose from with different features such as: First aid information Locating nearest Red Cross emergency shelters FEMA information...
-
E. ADA Coordination and Training:
Olympia shall train all present and future staff who work at Joe Louis Arena on any ADA issues relevant to their position at Joe Louis Arena, including but not limited to: (1) location...
-
11B-206.2.8 Employee work areas
Common use circulation paths located within employee work areas that are less than 1000 square feet (93 m2) and defined by permanently installed partitions, counters, casework, or furnishings...
-
1.16 Traditional, sloped-floor or traditional seating
Prior to the introduction of stadium-style seating in 1995, almost all seating in movie theaters was located on this type of sloped floor....
-
Tools and Documentation
at least 20 feet long a digital level or a bubble level that is at least 24 inches long a door pressure gauge a digital camera with a flash a copy of the 2016 Checklist for each location...
-
309 Operable Parts
Operable parts are required to be located with the reach ranges specified in 308....
-
11B-707.9.1 General
Where point-of-sale devices are provided, all devices at each location shall comply with Sections 11B-309.4, 11B-707.3, and 11B-707.7.2....
-
11B-245.2 Application
When a commercial facility is located in a private residence, that portion used exclusively in the operation of the commercial facility or that portion used both for the commercial facility...
-
R304.5.1 Width
If provided, flared sides of curb ramp runs and blended transitions shall be located outside the width of the curb ramp run or blended transition....
-
Outdoor Constructed Features in Common Use and Public Use Areas [F245.4]
common use and public use areas that serve picnic units with mobility features, at least 20 percent, but no less than one, of each type of outdoor constructed feature provided at each location...
-
Outdoor Constructed Features in Common Use and Public Use Areas [F244.3]
common use and public use areas that serve camping units with mobility features, at least 20 percent, but no less than one, of each type of outdoor constructed feature provided at each location...
-
R402.4 Reduced Vertical Clearance
The leading edge of the guardrail or barrier shall be located 685 mm (2.25 ft) maximum above the finish surface....
-
5.4.4.1 Transfer Support Distance from Transfer Surface for Stretchers
Transfer supports should be located along the long side of the transfer surface on the opposite side of the transfer....