Therefore, it is reasonable to assume that at least some minor deviation from absolute dimensions could be expected for water closets....
Search Results "Expected Maximum Flight Duration"
Filters
Commonly Searched Documents
-
4. ABSOLUTE DIMENSIONS
-
IMPLICATION OF A 19-INCH MINIMUM STANDARD FOR THE HIGHEST POINT IN THE LOWEST ADJUSTABLE POSITION
It is not unreasonable to expect that table and chair manufacturers will seek to compete by offering products with greater degrees of adjustability. Figure 3....
-
Executive Order 12866 (Regulatory Planning and Review), DOT Regulatory Policies and Procedures, and Executive Order 13563 (Improving Regulation and Regulatory Review)
The costs of this rulemaking are expected to be minimal for two reasons....
-
3.6.1. Hardware Replacement
Public comments on the 2014 NPRM, as well as information provided by manufacturers, suggest that captioning and audio description hardware is expected to last about 10 years. ...
-
V. RESERVATION OF RIGHTS
Olympia’s planned Events Center or relocation shall fail to meet the schedule set forth in paragraph 13: (i) Olympia shall immediately provide written notice to the United States of such expected...
-
3.2 Microphone Location
In programs in which audience participat ion is expected (as in a large lecture), then a wireless FM microphone should be available for audience use....
-
Areas for further work
Of course, it was not expected that all of these would be included in any one industry's standards, but they do indicate the range and complexity of issues related to construction tolerances...
-
Protruding Objects
Protruding Objects Common Problem: In areas inside and outside the lodging facility where people are expected to walk, objects protrude too far from the side, from posts, or hang down...
-
Pre-Event Attendee Registration and Communications
As attendees to our conference may experience multiple chemical sensitivities, please refrain from wearing all perfumes and use fragrance-free, unscented personal care products for the duration...
-
Salsbury Industries See Through Metal Locker
Requires the Registered User plan or above. Login! -
Safety
In short, part 382 is consistent with FAA safety requirements as it allows you to follow FAA safety rules and to ensure that the safe completion of the flight or the health and safety of...
-
Williams Sound PPA 457 NET PRO PERSONAL PA® PRO FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
Activar Hiawatha 535/509/536/537 Solid 1 inch Diameter Pulls
Since 1954, Hiawatha has been providing consistent customer service with the high-quality materials and finishes that you have come to expect. ...
-
Easter Seals El Mirador
We promote personal choice We do our work in an atmosphere of community inclusion CARF ACCREDITATION STATUS Easter Seals El Mirador was initially awarded the maximum...
-
Midmark 641 Barrier-Free® Power Procedures Chair
Narrow patient support surface, slim back section and tuck away side rails provide maximum patient accessibility and supports proper posture Powered seat, back, foot and tilt offer multi-positioning...
-
Hadrian Inc. Gladiator Athletic Lockers
Maximum Ventilation Fully ventilated doors and sides with 0.5” x 1” (13 mm x 25 mm) oval perforations allow for maximum air circulation as well as visual access....
-
AquaTrek2 ADA Wading Pool Ramp
The Wading Pool Ramp will have a slope ratio that is technically feasible, readily achievable, and is based on the ADA maximum extent feasibility requirements for any wading pool. ...
-
608.3.3 Alternate Roll-In Type Shower Compartments
Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls. Figure 608.3.3 Grab Bars for Alternate Roll-In Type Showers...
-
11B-604.8.3 Coat hooks and shelves
Shelves shall be located 40 inches (1016 mm) minimum and 48 inches (1219 mm) maximum above the finish floor. ...
-
Cross Slope
Comments indicated that specifications for cross slope (1:48 maximum) are not referenced in the curb ramp section. Response....
-
§382.133(a)
disability to use in the passenger cabin during air transportation an electronic assistive device specified in paragraph (c) of this section on all aircraft originally designed to have a maximum...
-
Width and Length
Width and Length Transfer walls must be a minimum of 12 inches wide to a maximum of 16 inches wide....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
239.2 Minimum Number
If a course is designed with the minimum 50 percent accessible holes, designers or operators are encouraged to select holes which provide for an equivalent experience to the maximum extent...
