Forces for pushing or pulling doors open are measured with a push-pull scale under the following conditions:...
Search Results "Break Out Opening"
Filters
Commonly Searched Documents
-
A4.13.11 Door Opening Force
-
A4.13.11 DOOR OPENING FORCE
Forces for pushing or pulling doors open are measured with a push-pull scale under the following conditions:...
-
Surface, Slope, and Openings [1011.2.2, 1011.2.3, and 1011.2.4]
Openings in the surface of the clear ground space must be small enough so that a sphere more than one-half inch in diameter cannot pass through....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3.
-
904.3.3 Check Writing Surfaces
Where provided, check writing surfaces shall comply with 902.3.
-
904.3.3 Check Writing Surfaces
Where provided, check writing surfaces shall comply with 902.3.
-
904.3.3 Check Writing Surfaces
904.3.3 Check Writing Surfaces. Where provided, check writing surfaces shall comply with 902.3.
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3.
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3.
-
4.7.5 Openings
Openings in surface of the clear floor or ground spaces required by section 2.0 shall not allow passage of a sphere more than 1/2 inch (13 mm) in diameter....
-
1.4.4. Operational Requirements
Because movie theaters may comply with the requirement to provide captioning at all screenings of a digital movie produced or distributed with such features through the provision of open...
-
4.13.11* DOOR OPENING FORCE
The maximum force for pushing or pulling open a door shall be as follows: (1) Fire doors shall have the minimum opening force allowable by the appropriate administrative authority....
-
Comparison of Single-User Toilet Room Layouts: Plan 3
An out-swinging door also minimizes the overall layout depth and cannot swing over the required clear floor space or clearance at any accessible plumbing fixture....
-
Track Crossing
Section 810.10 addresses track crossings at transportation facilities. The proposed rule required route surfaces to be level with the rail top, but permitted a 2 ½ inch gap at the...
-
T402.11 Gaps
When ramps or bridgeplates are deployed for boarding and alighting, gaps between the ramp or bridgeplate surface and floor of non-rail vehicles shall not permit passage of a sphere...
-
4.13.11(2)(b)
(b) interior hinged doors: 5 lbf (22.2N)
-
A4.13.11(3) Application of force
(3) Application of force: Apply force gradually so that the applied force does not exceed the resistance of the door. In high-rise buildings, air-pressure differentials may require a...
-
A4.13.11(3) Application of force
(3) Application of force: Apply force gradually so that the applied force does not exceed the resistance of the door. In high-rise buildings, air-pressure differentials may...
-
4.13.11(1)
(1) Fire doors shall have the minimum opening force allowable by the appropriate administrative authority....
-
Notice Requirement (Section-by-Section Analysis)
Several commenters recommended that the Department require a uniform system of labeling movies as having open captioning (OC), closed captioning (CC), or audio description (AD). ...
-
4.9.2 Treads and Risers
Open risers are not permitted....
-
13. Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas?
Do the provisions for openings in floor and ground surfaces in Section 302.3 apply to walking surfaces in play areas? Yes....
-
Re: 11B-904.3.4 Identification sign
when displayed, this section refers to "heck out aisles" instead of check out aisles...
-
Question 15
YES/NO 15. Is the full length (minimum 3 feet) of the lowered counters of the accessible checkout aisles and sales counters clear of merchandise and...