The proposed rule would have required the clear width of beach access routes to be 36 inches minimum....
Search Results "Clear Width at Turn"
Filters
Commonly Searched Documents
-
Beach Access Routes
-
Public Way
other parcel of land open to the outside air leading to a public street, which has been deeded, dedicated or otherwise permanently appropriated to the public for public use and which has a clear...
-
Valet Parking: ADA Standard Section 209.4
Section 209.4 covers scoping requirements in the current ADA Standards for passenger loading zones at valet parking.
-
Thresholds: ADA Standard Section 404.3.3
Section 404.3.3 covers the current ADA Standards for thresholds at automatic and power-assisted doors and gates.
-
Floor and Ground Surfaces: ADA Standard Section 503.4
Section 503.4 covers the current ADA Standards for the floor and ground surfaces at passenger loading zones.
-
11B-809.8.3 Door maneuvering clearance.
The width of the maneuvering clearance shall extend 18 inches (457 mm) beyond the strike edge at the pull side of the door....
-
R210.3 Shared Use Paths
width required for pedestrian access routes....
-
Seating Locations
An accessible seating plan requires aisles that are at least 36 inches wide and have sufficient turning space (e.g., a 60-inch diameter circle) in key locations throughout the room. ...
-
Tenon LLC
Remediate Issues When issues are found, Tenon helps turn internet noise into clear guidance so that you can get on with your work....
-
810.9 Escalators
Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see "Referenced Standards" in Chapter 1) and shall have a clear...
-
§ 38.125(c)(2) Ramp surface
The ramp or bridge plate surface shall be continuous and slip resistant, shall not have protrusions from the surface greater than 1/4 inch high, shall have a clear width of 30 inches and...
-
Water Play Components
If the surface of the accessible route, clear floor or ground spaces, and turning spaces that connect play components are submerged, the accessible route does not have to comply with the...
-
Doors and Gates in Series [§404.2.6]
Doors and Gates in Series [§404.2.6] At hinged or pivoted doors or gates in series, a separation is required that is at least 48” plus the width of doors or gates swinging into the space...
-
Yale Real Living™ Digital Door Viewer
The 105 degree viewing angle helps ensure a clear picture. The digital door viewers are simple to install on standard doors and easily powered with the included batteries....
-
Ramps
For each elevated ramp run: 12-inch (305 mm) maximum rise 1:12 maximum slope 36-inch (915 mm) minimum clear width ...
-
1003.3 Clearances
Although the minimum width of the clear pier space is 60 inches (1525 mm), it is recommended that piers be wider than 60 inches (1525 mm) to improve the safety for persons with disabilities...
-
1003.3 Clearances
Although the minimum width of the clear pier space is 60 inches (1525 mm), it is recommended that piers be wider than 60 inches (1525 mm) to improve the safety for persons with disabilities...
-
1003.3 Clearances
Although the minimum width of the clear pier space is 60 inches (1525 mm), it is recommended that piers be wider than 60 inches (1525 mm) to improve the safety for persons with disabilities...
-
Technical Requirements [1018 and 1018.1, Exception 3]
The technical requirements for beach access routes include specific provisions for connections, the surface, clear width, obstacles, openings, running slope, cross slope, resting intervals...
-
2.6 Passing Spaces
ORARs with a clear width less than 60 inches (1525 mm) shall provide passing spaces complying with 2.6 at intervals of 200 feet (61 m) maximum....
-
Floor and Ground Surfaces
interior and exterior accessible routes, including walking surfaces, ramps, elevators, and lifts stairways that are part of a means of egress required clearances, including clear...
-
FIGURE INDEX
Pile Height Figure 302.3 Elongated Openings in Floor or Ground Surfaces Figure 303.2 Vertical Change in Level Figure 303.3 Beveled Change in Level Figure 304.3.2 T-Shaped Turning...
