Ø The "accessible" toilet is placed too close or too far from the wall or stall divider. ...
Search Results "Control End Wall"
Commonly Searched Documents
-
Common Problems with Toilet Rooms
-
Section 36.204 Administrative Methods (Section-By-Section Analysis and Response to Comments)
or methods of administration that have the effect of discriminating on the basis of disability or that perpetuate the discrimination of others who are subject to common administrative control...
-
11. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
1k
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
1. Common Problems and Solutions in Website Accessibility
Resources providing more detailed information on accessible website design are provided at the end of this Chapter....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Terminal
Device or software with which the end user directly interacts and that provides the user interface....
-
Hallways
ADA Requirements Wall-mounted objects located between 27 inches and 80 inches above the floor may not protrude or stick out from the wall more than 4 inches....
-
704.3 Buildings on the same property and buildings containing courts
For the purposes of determining the required wall and opening protection and roof-covering requirements, buildings on the same property and court walls of buildings over one story in height...
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
1134A.7, Item 2
Reinforced walls for grab bars. ...
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
1134A.7, Item 1
Exception: The 48-inch (1219 mm) minimum clear width may be reduced to 36 inches (914 mm) for lavatories, cabinets, wing walls, or privacy walls located immediately adjacent to a water closet...
-
1134A.7, Item 2
Reinforced walls for grab bars....
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
-
E2-1. Pedestrian Routes
[ADA Stds. 4.4] Note: These objects may be wall mounted or free standing....
-
A4.4.1 General
The touch technique is used primarily in uncontrolled areas, while the diagonal technique is used primarily in certain limited, controlled, and familiar environments....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
8. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
- Salsbury Industries See Through Metal Locker Double Tier 3 Wide